Tektronix TLA 720 Скачать руководство пользователя

Страница: 15 / 214

General Safety Summary

TLA 720 Benchtop Chassis and TLA 7XM Expansion Chassis Service Manual

Provide Proper Ventilation.

Refer to the manual’s installation instructions for

details on installing the product so it has proper ventilation.

Terms in this Manual.

These terms may appear in this manual:

WARNING.

Warning statements identify conditions or practices that could result

in injury or loss of life.

CAUTION.

Caution statements identify conditions or practices that could result in

damage to this product or other property.

Terms on the Product.

These terms may appear on the product:

DANGER indicates an injury hazard immediately accessible as you read the
marking.

WARNING indicates an injury hazard not immediately accessible as you read the
marking.

CAUTION indicates a hazard to property including the product.

Symbols on the Product.

The following symbols may appear on the product:

Protective Ground

(Earth) Terminal

CAUTION

Refer to Manual

Double

Insulated

WARNING

High Voltage

Symbols and Terms

Содержание TLA 720























































































































































































































Результаты поиска

Содержание TLA 720

Отзывы:

Похожие инструкции для TLA 720

Бренды по названию

Популярные бренды

Tektronix TLA 720, Руководство по обслуживанию

Результаты поиска

Содержание TLA 720

Отзывы:

Похожие инструкции для TLA 720

Бренды по названию

Популярные бренды