manualshive.com logo in svg

Tektronix TLA 720, Руководство по обслуживанию

Поделиться
Скачать
Tektronix TLA 720 Скачать руководство пользователя страница 190

Replaceable Parts

TLA 720 Benchtop Chassis and TLA 7XM Expansion Chassis Service Manual

7–3

H

Instrument serial number

H

Instrument modification number, if applicable

If you order a part that has been replaced with a different or improved part, your
local Tektronix field office or representative will contact you concerning any
change in part number.

Change information, if any, is located at the rear of this manual.

Tektronix part numbers contain two digits that show the revision level of the
part. For most parts in this manual, you will find the letters XX in place of the
revision level number.  

670-7918-03

Part Number Revision Level

670-7918-XX

Revision Level May Show as XX

When you order parts, Tektronix will provide you with the most current part for
your product type, serial number, and modification (if applicable). At the time of
your order, Tektronix will determine the part number revision level needed for
your product, based on the information you provide.

Modules can be serviced by selecting one of the following two options. Contact
your local Tektronix service center or representative for repair assistance. 

Module Repair and Return. 

You may ship your module to us for repair, after which

we will return it to you.

New Modules. 

You may purchase replacement modules in the same way as other

replacement parts.

Using the Replaceable Parts List

This section contains a list of the mechanical and/or electrical components that
are replaceable for the Mainframe Use this list to identify and order replacement
parts. The following table describes each column in the parts list.  

Part Number Revision

Level

Module Servicing

Содержание TLA 720























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды