manualshive.com logo in svg

Tektronix TLA 720, Руководство по обслуживанию

Поделиться
Скачать
Tektronix TLA 720 Скачать руководство пользователя страница 40

TLA 720 Benchtop Chassis and TLA 7XM Expansion Chassis Service Manual

2–1

Operating Information

This chapter contains information about operating the benchtop chassis. Refer to
the TLA 700 Series Installation Manual for information on how to install and
configure the benchtop chassis. For more detailed operating information, refer to
the TLA 700 Series Logic Analyzer User Manual and in the online help. 

Figure 2–1 shows the front view of the benchtop chassis with a benchtop
controller installed. Figure 2–3 shows the rear view of the benchtop chassis.
Chassis slots 3 through 11 are labeled on the top and bottom of the chassis.
Slots 0, 1 and 2 are reserved for the three slot-wide controller, all other slots are
available for any other TLA 700 Series module.

Figure 2–1: Front view of the benchtop chassis with a benchtop controller

Содержание TLA 720























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды