Tektronix 310A Скачать руководство пользователя страница 64

Страница: 64 / 132

Performance C heck/C alibration-Type

310A

f. Disconnect the input signal.

g. CHECK-=-CRT display for straight line near the center

horizontal line.

15. Check Low-Frequency Linearity

a. Reconnect the standard amplitude calibrator to the

vertical INPUT connector with the 42 inch BNC cable.

b. Set the standard amplitude calibrator for a 0.5-volt

square-wave output.

c. Position the display to the center of the graticule

with the VER TICA L POSITION control.

d. Reduce the display to exactly two divisions with the

Variable VO LTS /D IV control (keep display centered about

the center horizontal line).

e. Position the top of the display to the top horizontal

line of the graticule.

NOTE

Tolerances given in this step are typical values pro
vided as guides to correct instrument operation, and
are not instrument specifications.

f. CHECK- Vertical compression of display does not

exceed 0.1 division or expansion does not exceed 0.15

division.

g. Position the bottom of the display to the bottom

horizontal line of the graticule.

h. CHECK-Vertical compression of display does not

exceed 0.1 division or expansion does not exceed 0.15

division.

i. Set the Variable VO LT S /D IV control to C A LI

BRATED.

j. Disconnect all test equipment.

16. Adjust Hum Balance

PERFORMANCE CHECK ONLY

This step is not applicable to a performance check.

Proceed to next equipment required picture (Fig.

5-11).

a. Set the VO LT S /D IV switch to .01.

b. Connect the vertical INPUT connector to one of the

ground posts on the front panel with the 18-inch BNC-to-

banana plug patch cord.

c. Connect the 10X probe to the test oscilloscope input

connector.

d. Set the test oscilloscope for a vertical deflection

factor of 0.05 volts/division (0.5 volts/division at probe

tip), AC coupled, at a sweep rate of five milliseconds/

division.

e. Connect the 10X probe tip to the hum balance test

point (see Fig. 5-10A). Connect the probe ground strap to

the Type 310A chassis near the test point,

f. ADJUST—Hum Balance adjustment, R470 (see Fig.

5-10B), for minimum vertical deflection on the test oscillo

scope.

g. Disconnect all test equipment.

Fig. 5 -1 0 . (A ) Lo cation o f hum balance tost p o in t (to p ), (B) loca

tio n o f H u m Balanco adjustm ent H eft side).

5-14

Содержание 310A





































































































































Результаты поиска

Содержание 310A

Отзывы:

Tektronix 310A, Инструкция по эксплуатации, Страница: 64 / 132

Результаты поиска

Содержание 310A

Отзывы: