Tektronix 310A Скачать руководство пользователя страница 60

Страница: 60 / 132

Performance Check/Calibration-Type 310A

F<g. 5-4. Lo cation of DC Bal a d ju itm a n t (lo ft tid a l,

PERFORMANCE CHECK O NLY

The remainder of this step is not applicable to a

performance check. If there is no trace on the CRT at

this point, adjust the PRESET ADJUST as follows

(this procedure may not provide correct instrument

performance under all operating conditions): (1)

Rotate the PRESET ADJUST fully counterclockwise

and then slowly rotate it clockwise until a trace first

appears on the CRT; note the physical rotation of the

adjustment. (2) Continue rotating the PRESET

ADJUST until the trace brightens; again note the

rotation. (3) Set the PRESET ADJUST midway

between the position noted in parts (1) and (2). (4)

Proceed to next step.

b. Connect the 10X probe to the test oscilloscope input

connector.

c. Set the test oscilloscope for a vertical deflection

factor of 0.5 volts/division (5 volts/division at probe tip),

DC coupled, at a sweep rate of one millisecond/division.

d. Connect the 10X probe tip to the preset test point

(junction of C101-R100. see Fig. 5-5A). Connect the probe

ground strap to the Type 31OA chassis near the test point.

e. Rotate the PRESET ADJUST, R126 (see Fig. 5-5B),

fully counterclockwise. Then, slowly rotate it clockwise

until the trace first appears on the Type 310A CRT. Adjust

the test oscilloscope vertical position control to move the

trace to a graticule line near the center horizontal line.

f. Continue rotating the PRESET ADJUST clockwise

until the trace on the Type 310A CRT brightens. Note the

location of the trace on the oscilloscope CRT.

g. A D JUST-Rotate the PRESET ADJUST counter

clockwise until the trace on the test oscilloscope is located

half way between the trace location in parts e and f.

h. Disconnect all test equipment.

Fig. 5 6 . (A ) Lo catio n o f p raia t t a il p o in t (inside swing-out chassis),

(B) location of P R E S E T A D J U S T (fro n t panal).

8. Check/Adjust Astigmatism

a. Connect the CAL OUT binding post to the vertical

INPUT connector with the 18-inch BNC-tobsnana plug

patch cord.

b. Set the CALIBRATOR switch to .5.

c. Center the display on the CRT area with the V E R T I

CAL POSITION and HORIZO NTAL POSITION controls.

d. C H E C K -C R T display should be well defined with

optimum setting of the FOCUS CONTROL.

PERFORMANCE CHECK ONLY

Rear-panel operational adjustment; can be adjusted as

part of a performance check.

e A D JU ST-FO C US control and ASTIG adjustment.

R750 (see Fig. 5-6), for best definition of the CRT display.

9. Check/Adjust CRT Alignment

a. Connect the vertical INPUT connector to one of the

ground posts on the front panel with the 18-inch BNC-to-

banana plug patch cord.

b. Position the trace to the center horizontal line with

the VER TICA L POSITION control.

5-10

Содержание 310A





































































































































Результаты поиска

Содержание 310A

Отзывы:

Tektronix 310A, Инструкция по эксплуатации, Страница: 60 / 132

Результаты поиска

Содержание 310A

Отзывы: