manualshive.com logo in svg

Tektronix 310A, Инструкция по эксплуатации, Страница: 11 / 132

Поделиться
Скачать
Tektronix 310A Скачать руководство пользователя страница 11

Operating  Instructions-Type 310A

3.  If  converting  from   117-volt  to  234-volt  nominal  line 

voltage  or  vice  versa,  change  the  line-cord  power  plug  to 

match  the  power-source  receptacle  or  use  a  suitable  adap­

ter.

4.  If  converting  from   117-volt  to  234-volt  nominal  line 

voltage or vice versa, change  the  line fuse as follows:

117-volts nominal 

1.6 ampere, slow-blow

234-volts  nominal 

0.8  ampere, slow-blow

5. 

Change  the  voltage  tag  on  the  rear  of the  instrument 

to  indicate  the  correct regulating  range.  The  new tag can  be 
obtained  from   your  local  Tektronix  Field  Office  or  repre­
sentative.  State the regulating range desired.

This  instrument  is  designed  to  be  used  w ith  a  three-wire 

AC  power  system.  If  a  three- to  two-wire adapter is used  to 
connect  this  instrument to a two-wire AC  power system, be 
sure  to  connect  the  ground  lead  o f  the  adapter  to  ground. 

Failure  to  complete  the  ground  system  may  allow  the 
chassis  to  be  elevated  above  ground  potential  and  pose  a 

shock  hazard.

Operating Temperature

The Type 310A  is cooled  by  convection  air flo w  through 

the  holes  in  the  cabinet.  For  this  reason,  it  is  im portant to 
choose  a  location  fo r  the  instrument  where  the  air  flo w   is 

not  restricted  or  the  temperature  of  the  cooling  air  is  not 
higher  than  the  ambient  temperature.  The  clearance  pro­

vided  by  the  feet  at  the  bottom   and  rear  should  be  main­
tained. A llo w  several  inches clearance on the sides.

A  thermal  cutout  provides  thermal  protection  and  dis­

connects  the  power  to  the  instrument  if  the  internal  tem­
perature  exceeds a  safe  operating  level.  If  the  thermal  cut­
out  opens  frequently,  choose  a  different  location  fo r  the 
instrument  which  provides  better  air  circulation,  or  pro­

vides  forced-air  cooling.  An  accessory  fan  base  is  available 
fo r  use  w ith  the  Type  310A.  This  fan  base  is  particularly 

useful  when  the  Type  310A  is  placed  in  a  permanent  loca­

tion.  In  addition  to  providing  forced-air  cooling,  the  fan 
base  elevates  the  fro n t  of  the  instrument.  This  makes  it 
easier  to   view  the  display  and  adjust  the  front-panel  con­
trols.  The  fan  base  can  be  ordered  through  your local  Tek­
tronix  Field  Office  or representative.

Operating Position

Rubber  feet  are  provided  both  on  the  bottom   and  rear 

of  the  Type  310A.  In  some  locations,  it  may  be  easier  to 
view  the display when  the instrument  is set on  the  rear feet. 
Flowever,  the  air  flo w   through  the  instrument  is  restricted 
in  this  position  reducing  the  cooling  effeciency.  Therefore, 

the  instrument  may  overheat.

CONTROLS A N D   CONNECTORS

General

A  brief  description  of  the  function and  operation o f the 

front-  and  rear-panel  controls  and  connectors  follows.  Fig. 
2-2  shows  the  fro n t  and  rear  panels  of  this  instrument. 

More  detailed  inform ation  is  given  in  this  section  under 
General  Operating  Information.

Cathode-Ray Tube  (CRT)

FOCUS 

Provides  adjustment  fo r  a well  defined
display.

INTENSITY 

Controls brightness of  display.

SCALE  ILLU M  

Dual  purpose  control  to  determine 

graticule  illumination  and  to  apply 
power  to  the  instrument.  In  the  fu lly  
counterclockwise  position,  power  is 
o ff.  As the control  is rotated  clockwise 

out  of  the  detent,  power  is  applied  to 
the  instrument  and  the  graticule lights 
come  on  at  maximum  intensity.  Con­
tinued  rotation  o f  the  control  reduces 
the graticule  illum ination.

Vertical

VO LTS/D IV 

Selects  vertical  deflection  factor  in

1-2-5  sequence  (Variable  VO LTS/D IV 

control  must  be  in  C ALIBR ATED  
position fo r indicated deflection).

Variable VO LTS/ 
DIV  (not  labeled- 
red  knob concen­

tric w ith  VO LTS/ 

DIV switch)

Provides  continuously  variable  uncali­
brated  deflection  factors  between  the 
calibrated  settings  of  the  VO LTS/D IV 

switch.  U N CALIBRATED V E R TIC A L 

light  at  lower  right  corner  o f  fro n t 
panel  indicates  when  the  Variable 

V O LTS/D IV  control  is  not  in  the 
C ALIBR ATE D   position.

INPUT 

Input  connector  fo r vertical deflection

signals.

Input  Coupling 

Determines  method  o f  coupling  input 

(AC-DC) 

signal  to vertical  amplifier.

AC:  DC  component  of  input signal  is 

blocked.  Low  frequency  - 3   dB 
point  is  about  two  hertz.

DC:  A ll  frequency  components o f the 

input  signal  are  passed  to  the  ver­

tical  amplifier.

2-3

Содержание 310A





































































































































Отзывы:

Нет отзывов