manualshive.com logo in svg

Tektronix 310A, Инструкция по эксплуатации, Страница: 45 / 132

Поделиться
Скачать
Tektronix 310A Скачать руководство пользователя страница 45

SECTION 4

 

MAINTENANCE

Type 310A

Change  inform ation,  if any, affecting this section  w ill  be found  at the rear o f the manual.

Introduction

This section o f the  manual  contains maintenance  inform ­

ation  for  use  in  preventive  maintenance,  corrective  mainte­

nance or troubleshooting  of the Type 310A.

Panel  Removal

The  side  panels  of  the  Type  310A  are  held  in  place  by 

slotted  fasteners.  To  remove  the  panels,  turn  each  fastener 
counterclockwise  several  turns  w ith  a  screwdriver.  Then, 
pull  the  panel  out  at  the  top  and  lift away  from   the  instru­
ment.  For  best  overall  operation  and  safety,  leave  the 
panels  on  this  instrument  except  during  calibration  or 
maintenance.

WARNING

Dangerous  potentials  exist  at  several  points  in  the 
instrument.  When  this  instrument  is  operated  w ith 

the  covers  removed,  do  not  touch  exposed  connec­
tions  or  components.  Disconnect  power  before clean­

ing the  instrument or  replacing  parts.

Access to  Internal Components

The  components  o f the Type 310A are mounted on  two 

separate  chassis which  are hinged at  the rear. The chassis on 
the  right  side  o f  the  instrument  may  be  swung  out to gain 
access  to  components  mounted  on  the  inner  sides  of  the 

chassis.  To  separate  the  chassis, loosen  the slotted fastener, 
located  at  the  lower  fro n t  corner  on  the  right  side,  several 
turns  and  swing  the  chassis  open.  The  instrument  can  be 
operated  w ith   the  chassis  open  fo r  troubleshooting.  How­

ever,  overall  instrument  performance  may  be  somewhat 

lower when operated  in this manner.

P R E V E N T IV E   M A IN TEN A N C E

General

Preventive  maintenance  consists  o f  cleaning,  visual 

inspection,  lubrication,  etc.  Preventive  maintenance  per­

formed  on  a  regular  basis  may  prevent  instrument  break­

down  and  w ill  improve  the  reliability  o f  this  instrument. 
The  severity  o f the environment to which the Type 310A  is 
subjected  determines  the frequency o f  maintenance. A  con­
venient  tim e  to  perform  preventive  maintenance  is  pre­
ceding  recalibration o f the instrument.

Cleaning

General. 

The  Type  310A  should  be  cleaned  as  often  as 

operating  conditions  require.  Accumulation  o f  d irt  in  the 

instrument  can  cause  overheating  and  component  break­

down.  D irt on  components acts as an  insulating blanket and

prevents  efficient  heat  dissipation.  It  also  provides  an  elec­
trical  conduction  path  and  may  result  in  instrument failure.

CAUTION

Avoid  the  use  of  chemical  cleaning  agents  which

m ight  damage  the  plastics  used  in  this  instrument.

Avoid  chemicals  which  contain  benzene,  toluene,
xylene, acetone or similar solvents.

Exterior. 

Loose  dust accumulation on the outside o f the 

Type  310A  can  be  removed  w ith  a soft cloth  or small  paint 

brush.  The  paint  brush  is  particularly  useful  fo r  dislodging 
d irt  on  and  around  the  front-panel  controls.  D irt  which 
remains  can  be  removed  w ith  a  soft  cloth  dampened  in  a 
mild  detergent  and  water solution.  Abrasive cleaners should 
not  be used.

CRT. 

Clean  the  plastic  light  filte r,  graticule  and  the 

CRT  face  w ith  a  soft,  lint-free  cloth  dampened  w ith  dena­
tured alcohol.

Interior. 

Dust  in  the  interior  o f  the  instrument  should 

be  removed  occasionally  due  to  its  electrical  conductivity 
under  high-hum idity  conditions.  The  best  way  to  clean the 
interior  is  to  blow  o ff  the  accumulated  dust w ith   dry,  low- 

pressure  air.  Remove  any  d irt  which  remains  w ith   a  soft 
paint  brush  or a  cloth  dampened w ith  a  mild  detergent and 
water  solution.  A   cotton-tipped  applicator  is  useful  for 
cleaning  in  narrow  spaces  or  fo r  cleaning  ceramic  terminal 
strips.

The  high-voltage  circuit  should  receive special attention. 

Excessive  d irt in  this area  may cause high-voltage arcing and 
result in  improper  instrument operation.

Lubrication

G en eral. 

The  reliability  o f  potentiometers,  rotary 

switches  and  other  moving  parts  can  be  maintained  if they 
are  kept  properly  lubricated.  Use  a  cleaning-type  lubricant 

(e.g.,  Tektronix  Part  No.  006-0218-00)  on switch  contacts. 
Lubricate  switch  detents  w ith   a  heavier  grease  (e.g.,  Tek­

tron ix  Part  No.  006-0219-00).  Potentiometers  which  are 
not  permanently  sealed  should  be  lubricated  w ith   a  lub ri­
cant  which  does  not  affect  electrical  characteristics  (e.g., 

Tektronix  Part  No.  006-0220-00).  The  pot  lubricant  can 
also  be  used  on  shaft  bushings.  Do  not  over  lubricate.  A 

lubrication  k it  containing  the  necessary  lubricants  and 

instructions  is  available  from   T ektronix,  Inc.  Order  Tek­

tron ix  Part  No.  003-0342-00.

4-1

Содержание 310A





































































































































Отзывы:

Нет отзывов