Tektronix 310A Скачать руководство пользователя страница 52

Страница: 52 / 132

Performance Check/Calibration—Type 31OA

4. Standard amplitude calibrator. Am plitude accuracy,

w ithin 0.25%; signal amplitude, 50 m illivolts to 100 volts;
output signal, square wave and positive DC; must have

m ix e d display feature. Tektronix calibration fixture
067-0502-00 recommended.

5. Square-wave generator. Must have the following o u t

put  capabilities  (may  be  obtained  from   separate  genera
tors):  120  volts  amplitude  at  50  hertz  and  one  kilohertz
repetition  rate  with  a  120  nanosecond  or  less risetime;  500

m illivolts into 50 ohms at 400 kilohertz w ith a five nano

second risetime. Tektronix Type 106 Square-Wave Genera
to r recommended (meets both output requirements).

6. High-frequency constant-amplitude sine-wave genera

tor.  Frequency,  350  kilohertz  to  above  four  megahertz;
reference  frequency,  50  kilohertz;  output  amplitude,  vari
able  from   five  m illivolts  to  five  volts  peak  to  peak  into  50
ohms;  amplitude accuracy, output amplitude constant w ith

in 3% o f reference at 50 kilohertz as output frequency

changes. Tektronix Type 191 Constant Am plitude Signal
Generator recommended.

7. Low-frequency constant-amplitude sine-wave genera

tor.  Frequency,  two  hertz  to  500  kilohertz;  output  ampli
tude,  variable  from   0.4  to 20 volts peak  to peak;  amplitude
accuracy,  output  amplitude  constant  w ithin  3%  of  refer
ence  at  one  kilohertz  as  output  frequency  changes.  For
example, General  Radio  Model  1310-A Oscillator.

8. Time-mark generator. Marker outputs, 0.1 micro

second to 0.2 second; marker accuracy, w ithin 0.1%.
Tektronix Type 184 Time-Mark Generator recommended.

Accessories

NOTE

For instruments between SN 10,000 and 19,119 use

comparable accessories which fit UHF connectors or
use suitable adapters.

9. IX probe fo r test oscilloscope.1 Tektronix P6011

Probe recommended.

10. Patch cord. Length, 18 inches; connectors, BNC

p lu g -ja ck and banana plug-jack. Tektronix Part No.
012-0091-00 (supplied accessory for instruments above SN
20,475).

11. 10X probe fo r test oscilloscope.1 Tektronix P6006

Probe recommended.

12. C able. Impedance, 50 ohms; type, RG-58/U;

length, 42 inches; connectors, BNC. Tektronix Part No.

012-0057-01.

13. Adapter. Adapts GR874 connector to BNC male

connector. Tektronix Part No. 017-0063-00.

1 N o t required fo r perform ance check on ly.

14. 5X attenuator. Impedance, 50 ohms; accuracy,

±3%; connectors, BNC. Tektronix Part No. 011-0060-00.

15. Termination. Impedance, 50 ohms; accuracy, ±3%;

connectors, BNC. Tektronix Part No. 011-0049-00.

16. 2X attenuator. Impedance, 50 ohms; accuracy,

±3%; connectors, BNC. Tektronix Part No. 011-0069-00.

17. 10X probe fo r Type 310A. Tektronix P6012 recom

mended (supplied accessory).

18.

Adapter. BNC-to-post. Tektronix Part No. 012-

0092-00 (supplied accessory fo r instruments above SN-
20,475).

19. Adapter. Adapts BNC male to dual binding posts.

Tektronix Part No. 013-0094-00.

20. BNC T connector. Adapts tw o BNC male connec

tors to one BNC female connector. Tektronix Part No.

103-0030-00.

21. Patch cord. Length, 18 inches; connectors, banana

plug-jack both ends. T ektronix Part No. 012-0031-00.

Adjustment Tools

22. Screwdriver. Three-inch shaft, 3/32-inch b it for

slotted screws. Tektronix Part No. 003-0192-00.

23. Screwdriver.1 Three-inch shaft, #1 Phillips bit. Tek

tro n ix Part No. 003-0341-00.

24. Low-capacitance screwdriver.1 1

1/2-inch shaft.

Tektronix Part No. 003-0000-00.

25. Tuning rod1 Five inch fo r 0.100-inch (ID) hex

slugs. Tektronix Part No. 003-0301-00.

SHORT-FORM PROCEDURE

Type 310A, Serial No.

Calibration Date __________________

Calibrated By ___________________ _

1. Adjust - 1 5 0 V o lt Power Supply (R610)

Page

5-7

REQUIREMENT: - 1 5 0 volts, ±4.5 volts.

PERFORMANCE: - 1 5 0 volts, ± ____ volts.

2. Check +100 V o lt and +300-Volt Power

Page 5-8

Supplies

REQUIREMENT: +100 volts, ±3 volts. +300 volts, ±9

volts.

PERFORMANCE: +100 volts, ±

v o lts

+300 volts,

± -------volts.

5-2

Содержание 310A





































































































































Результаты поиска

Содержание 310A

Отзывы:

Tektronix 310A, Инструкция по эксплуатации, Страница: 52 / 132

Результаты поиска

Содержание 310A

Отзывы: