manualshive.com logo in svg

Tektronix 310A, Инструкция по эксплуатации, Страница: 13 / 132

Поделиться
Скачать
Tektronix 310A Скачать руководство пользователя страница 13

Operating Instructions—Type 310A

ASTIG 

Screwdriver  adjustment  used  in  con­
junction  w ith  the  FOCUS  control  to 
obtain a well-defined  display.

CRT  CATHODE 

Input  binding  post fo r  intensity  modu­
lating signals.

GND 

Ground  terminal  to  establish  a  com­

mon  ground  between  this  instrument 

and  the  source  of  the  intensity  modu­

lating signal.

Sweep controls 

T IM E /D IV  
Variable

Horizontal  Display

500  [tSEC 
C ALIBR ATE D  
X I  MAG

Other controls

VERTICAL POSITION 

Midrange

HO RIZO NTAL  POSITION 

Midrange

Rear  Panel  controls

H O R IZ G A IN  

Clockwise

MAG  CENTER

HORIZ  GAIN

EXT  HORIZ 

INPUT

GND

Screwdriver  adjustment  to  set  the  DC 

level  of  the  horizontal  am plifier so de­

flection  at  the  center  of  the  display 
does  not  move  when  the  horizontal 

Display switch  is set to   X5 MAG.

Control  to   set  the  gain of the horizon­
tal  amplifier  fo r  external  horizontal
operation.

Input  binding  post  fo r  external  hori­

zontal  deflection signals.

Ground  terminal  to   establish  a  com­
mon  ground  between  this  instrument 
and  the source  of the external  horizon­
tal  deflection signal.

2.  Connect the Type 310A  to a  power source that meets 

the  voltage  and  frequency  requirements  of  the  instrument.

3.  Turn  the  SCALE  ILLU M   control  clockwise from   the 

PWR  OFF  detent  to  turn  on  the  instrument.  A llow  several 
minutes  warmup  so  the  instrument reaches a  normal  opera­
ting  temperature  before proceeding.

CRT Controls

4.  Advance  the  INTENSITY  control  until  the trace  is at 

the desired viewing  level  (about midrange).

5.  Connect  the  CAL  OUT  binding  post  to  the  vertical 

INPUT  connector  w ith  the  18-inch  BNC-to-banana  plug 

patch  cord  (supplied  accessory).  For  instruments  between 
SN 10,000  and  20,474  use  an  18-inch  banana-plug  patch 
cord.

SWEEP CAL 

Screwdriver  adjustment  to   set the gain
o f  the  horizontal  am plifier  fo r  correct 

normal  sweep timing.

FIR ST-TIM E  OPERATION

General

The  follow ing steps demonstrate  the  use  o f the controls 

and  connectors  of  the  Type  310A.  It  is recommended  that 
this  procedure  be  followed  completely  fo r  first  time fam il­

iarization w ith this instrument.

6.  Adjust  the  FOCUS  control  fo r  a  sharp,  well-defined 

display  over  the  entire  trace  length.  If  focused display can­

not  be  obtained,  see  Astigmatism  Adjustment  in  this sec­
tion.

7.  Rotate  the  SCALE  ILLU M   control  throughout  its 

range  and  notice  that  the  graticule  lines  are  illuminated  as 
the  control  is  turned  counterclockwise  (most  obvious  w ith 
tinted  filte r  installed).  Set  the  control  so the graticule lines 
are illuminated as desired.

Setup  Information

1. 

Set the front-panel  controls as follows: 

CRT controls

FOCUS 
INTENSITY 

SCALE  ILLU M

Midrange 
Counterclockwise 
PWR  OFF

Vertical  controls 

VO LTS/DIV 
Variable 

Input Coupling

.1

C ALIBR ATED

DC

Trigger controls

TRIGGER 

+ IN T

Trigger Coupling-Mode 

AUTO

TRIG  LEVEL 

Midrange

S T A B ILIT Y  

PRESET

Vertical  Controls

8.  Center  the  display  about  the  center  horizontal  line 

w ith  the  V E R TIC A L  POSITION  control.  The  display  is  a 
square  wave,  five  divisions  in  amplitude  w ith  about  five 
cycles  displayed.  If the display  is not five divisions  in ampli­
tude, see Vertical  Gain  Adjustm ent in this section.

9.  Temporarily  disconnect  the  input signal and  position 

the  trace  to   the  center horizontal  line w ith the VE R TIC A L 
POSITION  control.

10.  Reconnect  the  input  signal  to   the  vertical  INPUT 

connector.  Notice  that  the  baseline  o f  the  square  wave  is 

near the center horizontal  line.

11.  Set  the  Input  Coupling  switch  to  AC.  Notice  that 

the  waveform  is  centered  about  the  center  horizontal  line 

(ground  reference).

2-5

Содержание 310A





































































































































Отзывы:

Нет отзывов