TekTone Tek-CARE NC150N Скачать руководство пользователя страница 16

Страница: 16 / 32

System Installation

12 • IL380 Tek-CARE

NC150 & NC200 Manual

System Installation

System Checkout and Testing

IR151B, IR152B, IR155B Patient Stations: Test patient stations one at a time. Initiate

a call on each patient station: Press the button on the end of the call cord for IR151B

and IR152B Patient Stations (test both circuits on IR152B stations). Pull the call cord

on the IR155B.

Check for operation of the following signals:

• The

call

placed

lamp on the patient station should be illuminated.

• The LI381, LI382 or LI382LED Corridor Light near the room entrance should

be illuminated.

• On the NC150N or NC200N Master Station, the call lamp should be illuminated

and the associated station selector lamp (marked to identify the calling station)

should be illuminated. A slowly repeating audible call tone should be heard.

The normal call tone may be silenced by the

tone

off

button, which should be

illuminated to indicate tone silencing.

• On all LI150B Duty Stations, the

call

placed

lamp should be illuminated, and

a slowly repeating audible call tone should be heard. The normal call tone may

be silenced by the

tone

off

switch.

Reset the call at the patient station: Press the

reset

button on IR151B and IR152B

Stations. Push the

reset

switch to the left on IR155B Stations. All signals should

be canceled.
Test the intercom function:

• Initiate a call on each station as previously described.

• On the master station, select the calling station by pressing the illuminated station

selector button and check for the following:

1. The

station

selector

lamp should be canceled.

2. The

call

lamp should turn off.

3. The audible call tone should be canceled.

4. The remote station’s

use

LED should be illuminated.

• Press the

call

button and the

talk

button on the master station. An electronic

call tone should be heard at the master station and at the patient station.

• Press the

talk

button and speak in a normal voice. Release the button to hear

the reply.

• At the patient station, the

call placed

lamp should turn off, and the

in use

LED

should be illuminated.

• When voice communication is heard, reply in a normal voice.

• Return all controls to the normal position.

On each IR150B Staff Station, test operation the same as with the IR151B Patient

Station, except place a call using the

call

button instead of a call cord.

On each SF155B Emergency or SF156B Code station (one at a time), slide the call

switch down, and then check the following signals:

• The

call

placed

lamp should be flashing.

• The LI381, LI382 or LI382LED Corridor Light near the room entrance should

be flashing.

• On the master station, the

call

lamp should be flashing, the associated station

selector lamp (marked to identify calling station) should be flashing, and an

intermittent audible call tone should be heard. The

tone

off

button must not

cancel the emergency code call tone.

On all LI150B Duty Stations, check the following signals:

• The

call

placed

lamp should be flashing.

• The rapidly pulsing audible call tone should be heard. The

tone

off

switch must

not cancel the emergency call tone.

Содержание Tek-CARE NC150N
































Результаты поиска

Содержание Tek-CARE NC150N

Отзывы:

Похожие инструкции для Tek-CARE NC150N

Бренды по названию

Популярные бренды

TekTone Tek-CARE NC150N, Руководство по эксплуатации и установке

Результаты поиска

Содержание Tek-CARE NC150N

Отзывы:

Похожие инструкции для Tek-CARE NC150N

Бренды по названию

Популярные бренды