background image

System Installation

8 • IL380 Tek-CARE

®

 NC150 & NC200 Manual

Copyright © TekTone Sound & Signal Mfg., Inc. All Rights Reserved.

SS100 24 VAC 100 VA Transformer: Locate the SS100 within 3 feet of the PK800A 

Secondary Power Supply. Do not exceed operating temperature range of 10–30°C.

Wiring Installation

Run wiring conduit from corridor light to corridor light and terminate at the PK151A 

or PK152 Power & Control Unit. Limit each run to 15 corridor lights, 15 stations and 

600 feet of wire. Refer to 

Wiring Diagrams

 section for additional connection and 

cabling information, starting with 

Figure 9

. Select conduit size to accommodate the 

following cables:

•  4 cond. #18 common to all stations (except LI150B Duty Stations). Add 2 cond. 

#18 common if LI382 or LI382LED Corridor Zone Lights are used. 

•  2 cond. #22 selective for each IR150B, IR151B, IR152B and IR155B Station in 

the system. Shielded cable must be used.

•  1 cond. #22 selective for each SF155B Emergency Station or SF156B Code Station 

not used in conjunction with a patient station.

•  4 cond. #18 to one LI150B Duty Station.

System Installation

Panel Removal:

 First remove the 

self-tapping metal screws located in 

the top U-channel just above each 

panel. Then lift up on panel to clear 

bottom channel. After removal, 

adequate space is available to grasp 

and remove the remaining panels.

Panel Replacement:

 Insert top of 

panel into top channel, push panel in 

at bottom, and release. Panel should 

fall into place in bottom channel. 

Replace self-tapping metal screws.

Figure 4—Panel Removal 

and Replacement

Figure 3—Master Panel Housing Chart 

and Wall Cut-Out Details

 

Housing 

Wall Opening

 Flush  Surface  Width (B)  Height

 OH202 

OH302 

8.5" 

16.25"

 OH203 

OH303 

12.5" 

16.25"

 OH204 

OH304 

16.5" 

16.25"

 OH205 

OH305 

20.5" 

16.25"

In masonry walls, install 0.5"×4" wood 

fillers  at  top  and  bottom  of  opening  for 

housing attachment.

Содержание Tek-CARE NC150N

































Отзывы: