background image

IL380 Tek-CARE

®

 NC150 & NC200 Manual • 1

Copyright © TekTone Sound & Signal Mfg., Inc. All Rights Reserved.

System Operating Instructions

This section provides complete operating instructions for all Tek-CARE

®

 functions, 

as well as reference drawings for use in locating and describing all controls. System 

operators must read the following operating instructions concerning system equipment 

and the terms used in conjunction with the equipment.

NC150N, NC200N Master Stations

Refer to 

Figure 1

 for locations, names, and functions of controls and indicators.

Answer Normal Calls:

Normal calls are indicated by simultaneous operation of the following signals:
•  Steady illumination of the associated station selector lamp which is marked to 

indicate call origin.

•  Steady illumination of call lamp.
•  Slowly pulsing audible tone. The audible call signal may be canceled for normal calls 

by pressing the 

tone

 

off

 button. The button will then illuminate to indicate the tone 

is silenced. Pressing the 

tone

 

off

 button when illuminated resets the call tone.

To establish conversation with the calling station, press the associated station 

selector button. The remote station’s 

reset

 lamp will illuminate. To speak to the 

caller, press the 

talk

 button while speaking and release to listen.

When the conversation is complete, press the associated station selector button to 

release the station. The remote station’s 

reset

 indicator will turn off. Normal calls 

placed from an IR155B Station must be canceled at the point of origin.

Answer Normal Calls Using Optional TA150N or TA200N Handset:

To establish conversation with the calling station, press the associated station selector 

button. The remote station’s 

reset

 

lamp will illuminate. To speak to the caller, lift 

the handset from the cradle and begin normal two-way conversation. When the 

conversation is complete, press the associated station selector button to release the 

station. The remote station’s 

reset

 

lamp will turn off. Replace the handset in the cradle. 

Normal calls placed from an IR155B Station must be canceled at the point of origin.

Answer Emergency Calls: 

All emergency calls take precedence over any normal call signal. Emergency 

calls must be answered in person and can only be canceled from point of origin. 

Emergency calls are indicated by simultaneous operation of the following signals:
•  Rapid flashing of the associated station selector lamp, which is marked to indicate 

call origin.

•  Rapid flashing of call lamp.
•  Rapidly pulsing audible tone.

Содержание Tek-CARE NC150N

































Отзывы: