Teknor Industrial Computers PCI-934, Техническое справочное руководство

Страница: 27 / 124

PCI-934 Technical Reference Manual
6-4
Recommended DRAM devices are listed below. Many other models are also available and
function equally well. Please check with your local distributors for comparable substitutes.
SIMM VENDOR PART # SIMM VENDOR PART #
1M*36 (FPM) Centon CXCGF6JF1XS283T 4M*32 (EDO) Abbacom Log 112-01643244-S6T
4MB modules Centon CTK1MX36-70SMT 16MB modules Centon CTK4MX32-60EST
Hyundai HYM536120AW-60 Micron MT8D432DM-6X
Micron MT9D136M-7 Unigen 4X32NEC6KBT2EDO
Nec MC-421000A36B-70 Unigen UG8M43222KBT-6
Samsung KMM5361000B-7 Unigen UG8M43222KBN-6
Texas Inst. TM124MBK36R-70 4M*36 (FPM) Centon CKEGH6TF2XS121T
Toshiba THM361020AS-70 16MB modules Centon CTK4MX36-60SMT
Unigen UG12M13600DBT-6 Hyundai HYM536410AM-70
Mitsubishi MH4M36ANXJ-7
2M*32 (EDO)
Centon CTK2MX32-60EST Nec MC-424000A36BH-70
8MB modules Micron MT4D232DM-6X Nec MC-424000A36BJ-70
Unigen 2X32NEC6KBT2EDO Samsung KMM5364100-7
Unigen UG16M23220DBT-6 Toshiba THM364020S-70
Unigen UG9M43602KBT-6
2M*36 (FPM) Centon CTK2MX36-60SMT 8M*32 (EDO) Centon CTK8MX32-60EST
8MB modules Hitachi HB56D236BW-7B 32MB modules Micron MT16D832DM-6X
Hitachi HB56D236B2-7C Unigen 8X32NEC6KBT2EDO
Hitachi HB56D236BS-7BC Unigen UG16M83222KBT-6
Hitachi HB56D236BW-7C
8M*36 (FPM)
Hitachi HB56D836BR-70A
Hyundai HYM536220W-70 32MB modules Hitachi HB56D836BR-60A
Hyundai HYM536220AW-60 AA Toshiba THM368020SG-60
Micron MT18D236M-7 Toshiba THM368020S-70
Nec MC422000A36B-70 Unigen UG18M83602KBT-6
Samsung KMM5362000B-7
16M*32 (EDO)
Unigen UG216E3254HKT-6
Toshiba THM362040AS-60 64MB modules
Toshiba THM362040AS-70 32M*32 (EDO) Unigen UG232E3244HKT-6
128MB modules Unigen UG232E3264HKT-6
To install the SIMMs in the sockets, proceed as follows:
1. With the board flat on the table, turn it so that
the bracket is on the right.
2. Hold the module with the notch on the bottom
right facing you, and insert the fingers into the
socket at a 70° angle from the board. Always
start inserting the module in the socket nearest
the top edge of the board
3. Snap the module to a vertical position. It is fully
installed when the retaining pegs snap into the
holes at each end of the module.
4. Work your way by inserting the other modules,
one by one, towards the lower edge of the board.
To remove SIMMs from sockets, pull on the retaining pegs located on each side of the
socket. Once the module has snapped out, pull gently on it.