Tecumseh VLV Скачать руководство пользователя страница 52

Страница: 52 / 64

695578

Oil level too high.

To check level turn dipstick cap tightly into receptacle for

accurate level reading.

Oil filler cap loose or gasket damaged causing

Replace ring gasket under cap and tighten tube securely.

spillage.

Engine speed too fast.

Using tachometer adjust engine RPM to spec.

Gaskets damaged or gasket surfaces nicked

Clean and smooth gasket surfaces. Always use new

causing oil to leak out.

gaskets.

Breather tube not connected to air cleaner.

Reconnect tube.

Using 10W30 oil under high load/high temperature

Replace with SAE 30 oil.

conditions.

Breather mechanism damaged or dirty causing

Replace breather assembly.

leakage.

Drain hole in breather box clogged causing oil to

Clean hole with wire to allow oil to return to crankcase.

spill out of breather.

Oil passages obstructed.

Clean out all oil passages.

Piston oil control ring return holes clogged.

Remove oil control ring and clean return holes.

Piston rings and grooves worn excessively.

Reinstall new rings and check land clearance and correct

as necessary.

Cylinder wall worn or glazed, allowing oil to

Bore cylinder for oversized piston & rings.

bypass rings into combustion chamber.

Piston fit undersized.

Measure and replace as necessary.

Valve guides worn excessively thus passing oil

Ream valve guide oversize and install 1/32'’ oversize valve

into combustion chamber.

and new valve seal if equipped.

Crankcase breather plugged.

Clean or replace breather.

Seal outside seat in cylinder or side cover is

Visually check seal receptacle for nicks and damage.

damaged, allowing oil to seep around outer

Replace P.T.O. cylinder cover, or small cylinder cover on

edge of seal.

the magneto end if necessary.

Old seal hardened and worn.

Replace seal.

Crankshaft seal contact surface is worn undersize

Check crankshaft size and replace if worn excessively.

causing seal to leak.

Crankshaft bearing under seal is worn excessively,

Check crankshaft bearings for wear and replace if

causing crankshaft to wobble in oil seal.

necessary.

13-3

Remedy and Reference

Cause

Engine Uses Excessive Amount of Oil

Table 1. 4-Cycle Engine Troubleshooting Chart (Continued)

Oil Seal Leaks

Содержание VLV

































































Результаты поиска

Содержание VLV

Отзывы:

Похожие инструкции для VLV

Бренды по названию

Популярные бренды

Tecumseh VLV, Руководство техника

Результаты поиска

Содержание VLV

Отзывы:

Похожие инструкции для VLV

Бренды по названию

Популярные бренды