Tecumseh VLV Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 64

background image

2-4

695578

The carburetor is a float feed, nonadjustable type, with a
one piece extruded aluminum body. The float bowl,
float, nozzle, and venturi are nonmetallic, minimizing the
corrosion and varnishing problems.

Gasoline (fuel) vapors are highly

flammable and can explode. Fuel

vapors can spread and be ignited by a spark or

flame many feet away from engine. To prevent

injury or death from fuel fires, follow these

instructions:

• NEVER fill fuel tank indoors. Fill fuel tank

outdoors in a well-ventilated area.

• Use only an approved red GASOLINE container

to store and dispense fuel.

• If fuel is spilled, DO NOT start engine. Move

machine away from area of spillage. Avoid
creating any source of ignition until fuel vapors
are gone.

Common service areas of the carburetor are contained
in the fuel bowl. These areas are the float, needle, seat
and main nozzle. All of these parts can be serviced
without removing the carburetor body from the engine.

NOTE

Be sure to check the cross holes on the body of the
nozzle and the main orifice in the bottom of the nozzle.

Compressed air can pierce the

skin and cause injury. DO Not use

your hand to check for leaks or to determine air

flow rates. Wear safety glasses to shield from

debris. Failure to do so could result in death or

serious injury.

7.

Use a rubber tipped tapered nozzle on air hose and
apply low pressure compressed air or use a
monofilament fishing line to remove any deposits
in the main jet or cross holes.

Float Bowl Service

1.

Be sure engine is outdoors and in a well-ventilated
area.

2.

Disconnect and plug the fuel line.

3.

Remove the bowl drain screw.

4.

Remove the float bowl by snapping the bale spring
towards the throttle end of the carburetor.

NOTE

Use care when using tools to remove the bail from the
carburetor. Failure to do so may result in bending the
retainer.

After the bowl gasket is removed, the parts contained in
the bowl can be inspected and serviced.
5.

Pull out the main nozzle and spring.

6.

Inspect the main nozzle for deposits.

WARNING

WARNING

Married System Main Jet

Split System Main Jet
Jet and Nozzle Ass'y.

"O" Ring

Air
Bleed
Holes

«
...
18
19
20
21
22
...
»

Содержание VLV

































































Отзывы:

Нет отзывов

Похожие инструкции для VLV

Бренд: GAS GAS Страницы: 71

Бренд: Westerbeke Страницы: 86

Бренд: VEM Страницы: 35

Бренд: AL-KO Страницы: 182

Бренд: YuanDong Страницы: 23

Бренд: Scania Страницы: 83

Бренд: ACM Страницы: 37

Бренд: Continental Motors Страницы: 146

Бренд: Farymann Diesel Страницы: 76

Бренд: RHINO Страницы: 20

Бренд: Paccar Страницы: 121

Бренд: Saito Страницы: 27

Бренд: Inel Страницы: 4

Бренд: Honda Страницы: 7

Бренд: DANA Страницы: 3

Бренд: DANA Страницы: 3

Бренд: DANA Страницы: 3

Бренд: DANA Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды