Tecumseh VLV Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 64

background image

695578

Alternator

The 350 Milliampere charging system consists of a
single alternator coil mounted to one side of the solid
state module.

CAUTION

NOTE

This charging system is designed to maintain a charged
battery. Most O.E.M.'s supply a trickle charger, which
should be used before and after off-season storage. This
system will maintain the charge level under normal use
conditions.

Do not operate engine with

charging system disconnected.

Doing so may result in damage to diode.

System Checking

NOTE

Set volt/ohm meter to 0-20 volt D.C. scale for test.
The battery MUST BE IN CIRCUIT for test to perform
properly.

1.

Connect voltmeter at the battery (should read
battery voltage).

2.

Next, start engine -voltage should read higher than
when engine is off.

NOTES

If there is a change upward in voltage, the charging sys-
tem is working.
If there is no change in voltage, the alternator should be
replaced.

Solid State Module

Alternator

Lamination Screws

Alternator Coil

Ignition Coil

Lamination Screw

Troubleshooting Electric Start Engines

The following is a list of possible problems and causes.

Dead Battery

Extended storage without charging
Excessive cranking
Faulty starter
Faulty wiring
Faulty alternator
Faulty battery

Battery O.K., Engine Won't Crank

Brake cable defective
Faulty starter switch
Poor electrical connections
Faulty starter. See starter section

Engine Cranks Slowly

Weak or discharged battery
Faulty starter

Troubleshooting for Both Mechanical and
Electric Start Systems

If Engine Pulls or Cranks Hard

Excessive engine drag due to obstructions under
deck.
Mower traction drive mis-adjusted
Valve clearance too wide
Compression release not functioning
Flywheel brake is still applied

Maximum compression should be 90 PSI (6.2 Bar). If
compression is higher, de-carbon the valve seat and
head area and check valve clearances. Exhaust valve
clearance may be set as low as .004'’ (.10 mm) if
necessary to gain more compression relief. If compres-
sion is still above 90 PSI (6.2 Bar), check the camshaft
compression relief mechanism.

Chapter 6

Alternator

6-1

«
...
36
37
38
39
40
...
»

Содержание VLV

































































Отзывы:

Нет отзывов

Похожие инструкции для VLV

Бренд: YOODA Страницы: 6

Бренд: Iveco Motors Страницы: 6

Бренд: Hatz Diesel Страницы: 56

BAUDOUIN PowerKit 16M33 Series

Бренд: WEICHAI Страницы: 142

Бренд: Shindaiwa Страницы: 44

Бренд: AL-KO Страницы: 144

Бренд: dunkermotoren Страницы: 32

Бренд: Barrus Страницы: 97

Бренд: Yamaha Страницы: 25

Бренд: Yamaha Страницы: 18

Бренд: Yamaha Страницы: 50

Бренд: Yamaha Страницы: 62

Бренд: Yamaha Страницы: 59

Бренд: Yamaha Страницы: 64

Бренд: Yamaha Страницы: 66

Бренд: Yamaha Страницы: 66

TRANSERVO SSC04

Бренд: Yamaha Страницы: 80

Бренд: Yamaha Страницы: 76

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды