Tecumseh VLV Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 64

background image

IMPORTANT NOTICE!

SAFETY DEFINITIONS

Statements in this manual preceded by the following
words are of special significance:

WARNING

or

WARNING indicates a potentially hazardous situation
which if not avoided, could result in death or serious
injury.

NOTE

Refers to important information and is placed in italic type.

It is recommended that you take special notice of all
items discussed on the next page and wear the
appropriate safety equipment.

Before operating this engine it is your responsibility to
read this Operator’s Manual. Follow these basic rules
for your personal safety:

• Keep this manual handy at all times for future

reference.

• Read it carefully and familiarize yourself with

operating, maintenance, components and

safety instructions

Notice Regarding Emissions

NOTE

Engines which are certified to comply with California and
U.S. EPA emission regulations for SORE (Small Off Road
Equipment), are certified to operate on regular unleaded
gasoline, and include the following emission control
systems: (EM) Engine Modification and (TWC) Three-
way Catalyst (if so equipped).

Tecumseh Website

Visit the Tecumseh website at:

www.TecumsehPower.com

«
1
2
3
4
...
»

Содержание VLV

































































Отзывы:

Нет отзывов

Похожие инструкции для VLV

Vickers M2-200 Series

Бренд: Eaton Страницы: 13

Бренд: BAFANG Страницы: 12

Бренд: Perkins Страницы: 92

Бренд: Hatz Diesel Страницы: 56

Бренд: Daytona Страницы: 18

Бренд: Zundapp Страницы: 52

Бренд: Waterworld Страницы: 30

Бренд: TOPMAQ Страницы: 17

Бренд: Hitachi Страницы: 41

Бренд: Hitachi Страницы: 1037

Бренд: Hitachi Страницы: 1104

Бренд: Yamaha Страницы: 76

Бренд: Yamaha Страницы: 72

Бренд: Yamaha Страницы: 96

Бренд: Yamaha Страницы: 94

Бренд: Yamaha Страницы: 99

Бренд: Yamaha Страницы: 128

Бренд: Yamaha Страницы: 135

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды