Tecumseh VLV Скачать руководство пользователя страница 56

Страница: 56 / 64

695578

Motor stalls under load.

Shorted field coil.

Correct, or replace housing assembly.

Shorted or open armature.

Replace armature.

Intermittent operation.

Break in electrical circuit.

Disconnect ignition cut-off wire at the engine.
Crank engine, if spark, check ignition switch,
safety switch and interlock switch. Check
wires for poor connections, cuts or breaks.

Loose or faulty electrical

Correct.

connections.

Dirty or oily commutator.

Clean and dress commutator.

Brushes binding in holders.

Free up brushes. Replace worn brushes and
those which have come in contact with
grease and oil.

Open armature.

Replace armature and interlock switch.

Sluggish disengagement

Dirt and oil on assembly and

Clean drive assembly and armature shaft

of the drive assembly

armature shaft.

and relubricate shaft splines.

pinion gear.

Bent armature.

Replace armature.

Remedy and Reference

Problem

Table 3. Troubleshooting 12 Volt Starters (Continued)

Probable Cause

13-7

Содержание VLV

































































Результаты поиска

Содержание VLV

Отзывы:

Похожие инструкции для VLV

Бренды по названию

Популярные бренды

Tecumseh VLV, Руководство техника

Результаты поиска

Содержание VLV

Отзывы:

Похожие инструкции для VLV

Бренды по названию

Популярные бренды