- 54 -
8.04 Tecweigh Protocol
There are two different approaches that serial users can employ for the following Remote
Calibration Section (8.05).
The Protocol Parameter (Section 6.02.45) permits two selections, they are TEC STD and TEC
OLD. The differences between these two styles, detailed in section 8.05 below, gives the user
more secure communications when set to TEC STD, and historical commands when set to TEC
OLD. Users with existing installations should use the TEC OLD version to avoid programming
changes, and new installations should use the new TEC STD version for a higher level of
security to prevent false commands from being accepted by the WP20.
8.05 Remote Calibration (see preceding section 8.04)
There are four commands that can be sent to the WP20 for Remote Calibration. Note that no data
is returned after calibration commands are sent. The characters are ASCII. Use the following
format to send the WP20 Remote Calibration commands:
[Station ID] [Command] [Carriage Return].
TEC STD
Command
Action
=R
Resets the TOTAL display
=Z
Starts an AUTO ZERO Cycle
=S
Starts an AUTO SPAN Cycle
=C
Cancels an AUTO ZERO or AUTO SPAN Cycle
Example: To start an AUTO SPAN cycle at Station G, send the following command:
[ Station ID ] [ Command ] [ Carriage Return ]
G (one character) =S (two characters) ^M (one character)
TEC OLD
Command
Action
30
Resets the TOTAL display
31
Starts an AUTO ZERO Cycle
32
Starts an AUTO SPAN Cycle
33
Cancels an AUTO ZERO or AUTO SPAN Cycle
Example: To start an AUTO SPAN cycle at Station G, send the following command:
[ Station ID ] [ Command ] [ Carriage Return ]
G (one character) 32 (two characters) ^M (one character)
Be careful not to send serial commands when there is someone working at that station. Serial
communications should only be done after the station is completely set up, calibrated, and in Run
Mode. Sending commands while in Program Mode could cause conflicts and corrupt data. The
WP20 ignores commands that it does not recognize and only detects and acknowledges a
framing error.
Содержание Tecweigh 20
