technoswitch ORYX200 Series Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 49

background image

ORYX202 ORYX204 ORYX208 Conventional Fire Panels

– INSTALLATION & OPERATION MANUAL

PRMAN-0047 ORYX200 S21 Fire Panel Range Rev 02.00 220224.docx

E&OE

- 32 -

2.1.8

ONE-MAN WALK TEST MODE

▪

The following procedure is used to put a zone into Test Mode:

Press and hold

for 3 seconds.

The Test LED and Zone 1 Fault /In Test/Disable LED will both flash rapidly
Yellow.

Press

to move on to the zone to

be tested.

Each press will advance the selection onto the next zone (i.e., two presses
will select zone 3) and this will be confirmed by the respective Zone Fault/In
Test/Disable LED flashing rapidly.

Confirm your selection by pressing

once.

The Test LED and the selected z

one’s Fault/In Test/Disable LED will now

be flashing fast Yellow.

To exit the walk test selection mode, wait for 10 seconds or press reset.

▪

The same procedure is used to remove a zone from Test Mode. Alternatively, for a quick exit from
Test Mode, push the Reset button.

When a zone is in test, the Fire LED for that zone, the General Fire LED, Buzzer, and all Sounders will go on
for eight seconds before automatically clearing the condition if the device in the field has been reset.

No relays will activate if a zone is in test, except those relays programmed to switch when Sounders are
Activated.

2.1.9

ADVANCED CONTROLS AND INDICATIONS

Symbol

Function

LED Indication

Description

Service Switch

General Disable Flashing Yellow.
Sounder Fault/Disable Flashing
Yellow.
Enable Controls Flashing Yellow.

Used to place panel in Service/Commission
mode. All outputs are disabled when the
switch is activated.

Boot Loader
Jumper

System Fault Flashing Yellow.

Used to place the panel in Boot loader mode
to upgrade panel firmware.
No control or circuits will be active in this
mode. A hardware reset is required to revert
to Normal.

Figure 30

Service Switch

NB:

The switch must be in the left position for normal operation.

Service Switch

«
...
30
31
32
33
34
...
»

Содержание ORYX200 Series


















































Отзывы:

Нет отзывов

Похожие инструкции для ORYX200 Series

Бренд: Canon Страницы: 2

Бренд: Ebyte Страницы: 34

Бренд: YASKAWA Страницы: 61

Бренд: Panasonic Страницы: 15

Бренд: Panasonic Страницы: 42

SolarCell Remote

Бренд: Samsung Страницы: 2

Бренд: Samsung Страницы: 20

7000-2 - Escalade RAID Controller

Бренд: 3Ware Страницы: 2

Бренд: Calsense Страницы: 74

Бренд: D+H Страницы: 36

Бренд: D-Box Страницы: 4

Бренд: D+H Страницы: 36

Бренд: jcm-tech Страницы: 8

Бренд: National Instruments Страницы: 40

Бренд: National Instruments Страницы: 28

Бренд: National Instruments Страницы: 7

Бренд: National Instruments Страницы: 22

Бренд: PUTCO Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды