TechnipFMC ALIV-QT-XP Скачать руководство пользователя страница 67

Страница: 67 / 80

Issue/Rev. 0.1 (2/20) ║ MN06201 • Page 67

13 – Maintenance

13.1

Enclosure Maintenance

Flame Path Inspection Criteria

Models: ALIV-QT-XP or ALIV-ST-XP

WARNING:

To prevent ignition of hazardous atmospheres, disconnect from main power

supply before opening the cover.

Installation/inspection/maintenance/repair/overhaul/reclamation of the AccuLoad in

the European Union must be performed by qualified personnel in accordance with

the applicable requirements of EN 60079-14, EN 60079-17, and EN 60079-19 in

addition to all local codes/regulations.

ii.

Installation/inspection/maintenance/repair/overhaul/reclamation of AccuLoad’s

relying upon the IECEx certification must be performed by qualified personnel in

accordance with the applicable requirements of IEC 60079-14, IEC 60079-17, and

IEC 60079-19 as required by local codes/regulations.

iii.

Guidance for equipment inspection and maintenance is provided by EN/IEC 60079-17:

“Electrical Apparatus for explosive gas atmospheres, “Inspection and maintenance

of electrical installations in hazardous areas” and should be utilized for the

inspection / maintenance process.

iv.

When performing maintenance that requires opening of the enclosure cover, all

flame paths, which are defined as the machined flanged surface between the

housing and the cover, shall be inspected to ensure that they are clean and

undamaged, no scratches, nicks, corrosion, or other defects that would affect the

integrity of the flame path are allowed. If defects are detected the equipment should

not be placed back into service until the issues are resolved.

Verify that all tapped cover bolt threaded locations in the enclosure are clean and

intact with no missing/stripped threads.

vi.

Verify that the cover bolts are the required M8 x 1.25-6g, Din 912, Steel Grade

12.9. Prior to reassembly apply a light coating of nickel based anti-seize such as

TechnipFMC P/N (646002401) to all bolt threads.

vii.

Verify that any blind threaded cover bolt holes do not have excessive grease /

anti-seize packed into them as this could cause hydraulic fractures of the enclosure

when the bolts are tightened.

viii.

Inspect to see that the environmental O-ring is correctly installed (seated into the

groove) and in good condition, no cracks etc. If defective replace to maintain

environmental protection. Grease cover flange with petroleum jelly or TechnipFMC

grease (P/N 644886401) before reattachment of the cover to the housing.

ix.

Follow cover bolt torquing procedure as outlined in section 12. When complete,

verify the flame path gaps as per the procedure.

AccuLoad IV Installation and Maintenance Manual

Maintenance

Содержание ALIV-QT-XP

















































































Результаты поиска

Содержание ALIV-QT-XP

Отзывы:

Похожие инструкции для ALIV-QT-XP

Бренды по названию

Популярные бренды

TechnipFMC ALIV-QT-XP, Руководство по установке и обслуживанию

Результаты поиска

Содержание ALIV-QT-XP

Отзывы:

Похожие инструкции для ALIV-QT-XP

Бренды по названию

Популярные бренды