TechnipFMC ALIV-QT-XP Скачать руководство пользователя страница 26

Страница: 26 / 80

Page 26 • MN06201 ║ Issue/Rev. 0.1 (2/20)

AccuLoad IV Installation and Maintenance Manual

Electronic Module Layouts

For the ST, QT and N4 models, all four switches in SW2 should be in the OFF position

during normal operation. For the SA model, SW2-3 and SW2-4 are used to select the

board set with which this A4M is associated (For SA model see section 10 for more information) .

There are special functions which can be activated on all of the AccuLoad models when

SW2-1 is set to ON. To activate the special functions, remove power from the AccuLoad,

set the switches to select the desired special function and then apply power to the module.

Once the special function is complete, all switches should be set to OFF for the ST, QT

and N4 models. For the AccuLoad SA, SW2-1 and SW2-2 should be set to OFF and,

SW2-3 / SW2-4 should be set according to the board set.

Table 11.

AccuLoad SA, SW2-1, and SW2-2 settings

SW2-1 SW2-2 SW2-3

SW2-4

Normal operation for model ST, QT, N4 and SA board set A

Normal operation for model SA board set B

Normal operation for model SA board set C

Normal operation for model SA board set D

Reserved

Force default IP address - 192.168.0.1

Erase configuration database

Erase all databases (configuration, transaction, event, driver)

Clear Security Passcodes

Force Touch Panel Recalibration

Reserved

Содержание ALIV-QT-XP

















































































Результаты поиска

Содержание ALIV-QT-XP

Отзывы:

Бренды по названию

Популярные бренды

TechnipFMC ALIV-QT-XP, Руководство по установке и обслуживанию

Результаты поиска

Содержание ALIV-QT-XP

Отзывы:

Бренды по названию

Популярные бренды