TechnipFMC ALIV-QT-XP Скачать руководство пользователя страница 5

Страница: 5 / 80

Issue/Rev. 0.1 (2/20) ║ MN06201 • Page 5

AccuLoad IV Installation and Maintenance Manual

Introduction

1 – Introduction

This manual provides guidance for the installation of AccuLoad preset models ST,

QT, N4 and SA. When installed following the guidelines contained in this manual, the

AccuLoad will provide many years of safe, accurate and reliable delivery control. This

manual addresses the requirements specific to the AccuLoad and it is assumed that

the installation designers and fabricators are familiar with the applicable industrial facil

ity construction standards specific to the particular facility. The ST and QT models are

designed for use in Class 1 Div 1, Zone 1 hazardous locations while the N4 and SA

models are designed for Class 1 Div 2 environments. If questions arise, please contact

our Field Service Response Center or Customer Support.

1.1

Warnings and Precautions

Before you begin please read all of the following warnings and cautions to reduce the

risk of injury, equipment damage or malfunction.

Emergency Shutdown

- The AccuLoad has an extensive set of built-in safety features.

IMPORTANT:

The AccuLoad should never be relied upon to act as the primary safety

system control for the flow valve and pump controls, i.e. emergency stop, overfill,

ground protection, etc. These should always be handled by separate systems specifi

cally designed for that application. For example Safety systems specifically to meet SIL

requirements. Any power control circuits from these external systems shall be wired in

series ahead of the AccuLoad to remove power to the ancillary devices.

Configuration

- The AccuLoad is shipped from the factory in a completely initialized

state and must be properly configured for the specific installation prior to operation. The

unit will not operate due to alarm conditions until the configuration is completed. Using

a PC running the AccuMate program is the best method to set the initial configuration,

but if AccuMate is not available, all configuration parameters are accessible through

the front panel.

Hazardous Voltages

- There are hazardous voltages involved in the installation

and maintenance of the AccuLoad and only qualified individuals should perform

this installation.

Hazardous Locations

- The ST and QT models are approved for use in an explosive

(Class I, Div. 1, Groups C & D and Zone 1 Ex d ia, IIB Gb) atmosphere but there are

specific installation methods required to produce a comprehensive explosion-proof

system. This manual provides guidance for the AccuLoad installation only. In general,

keeping the front cover bolted closed in accordance with the instructions in Appendix

(section 12) is the key to maintaining explosion protection.

Any modification of the AccuLoad housing invalidates the hazardous location

rating of the AccuLoad.

•

Do not replace the bolts in the front cover except with those supplied by the manufac

turer. Using unapproved bolts invalidates the explosion-proof rating of the enclosure

• Do not drill or machine the housing.
• Do not attempt to replace the touchscreen or glass except as part of the factory

supplied assembly.

Содержание ALIV-QT-XP

















































































Результаты поиска

Содержание ALIV-QT-XP

Отзывы:

Бренды по названию

Популярные бренды

TechnipFMC ALIV-QT-XP, Руководство по установке и обслуживанию

Результаты поиска

Содержание ALIV-QT-XP

Отзывы:

Бренды по названию

Популярные бренды