tecan sunrise Скачать руководство пользователя страница 33

Страница: 33 / 63

3. Installation

Procedure

2021-07

Instructions for Use for SUNRISE No. 30086638 Rev. No. 2.9

3.7

Installation of Instrument Control Software

Note

For more information about installing the software, see Magellan or

XFluor4 Instructions for Use, which can be found on the software CD.

3.8

Defining the Instrument Settings

This program enables the user to define the settings of:

•

Instrument modes

•

Filter definition

•

Measurement modes

CAUTION

IF USED IN THE IVD ENVIRONMENT, ONLY THE AUTHORIZED

PERSON IS ALLOWED TO CHANGE AND DEFINE THE “SUNRISE

INSTRUMENT SETTINGS”.

3.8.1

Installation of “SUNRISE Instrument Settings” Software

The “SUNRISE Instrument Settings” software is installed using the following
procedure:

1. Insert Tecan Detection Suite CD into the required CD ROM drive.

2. The setup dialog box is displayed. Click the service and settings button. Click

the setup

button for the “SUNRISE Instrument Settings”. The installation

program is started, which installs “SUNRISE Instrument Settings” onto your
computer

3. A series of dialog boxes will appear, read each one, enter any necessary

information and click

Next

to continue.

4. The files are then installed, and the program icon is created.

5. When the

Installation

Complete

dialog box appears, click

Finish

and the

“SUNRISE Instrument Settings” program is ready to be used.

3.8.2

Starting the “SUNRISE Instrument Settings”

In case an instrument is already connected to one of Tecan's programs, close the
program or disconnect the instrument.
The “SUNRISE Instrument Settings” software is started by clicking the “SUNRISE
Instrument Setti

ngs” icon on the desktop if present or go to

Start

–

Programs

–

Tecan

– and select “SUNRISE Instrument Settings”.

The following dialog box appears:

Содержание sunrise
































































Результаты поиска

Содержание sunrise

Отзывы:

Похожие инструкции для sunrise

Бренды по названию

Популярные бренды

tecan sunrise, Инструкция по эксплуатации

Результаты поиска

Содержание sunrise

Отзывы:

Похожие инструкции для sunrise

Бренды по названию

Популярные бренды