Thank you for choosing the Team Losi XXX-NT ADAM DRAKE, Edition 2. During the past year, I, along with Team Losi engineers
and team members, have done extensive testing and development to give you the truck you just purchased. In addition to the many
specialty parts used on my previous race winning truck. The AD2 includes a host of new and revised parts to increase durability and
handling that have helped me and my team mates get to the winners circle time and time again. I think you will find it is tougher, faster, and
easier to drive than anything out there. As you build your new XXX-NT AD2 kit, be sure to read and follow the instructions carefully and
don’t forget to check out the set-up and tuning tips in the back of this manual. I hope you will enjoy your new Team Losi XXX-NT AD2 as
much as I do and wish you much success. See you at the track!
Good Luck!
WEL
WEL
WEL
WEL
WELCOME XXX-NT
COME XXX-NT
COME XXX-NT
COME XXX-NT
COME XXX-NT AD2 O
AD2 O
AD2 O
AD2 O
AD2 OWNER!
WNER!
WNER!
WNER!
WNER!
NOTES & SYMBOLS USED
Step A-1
This is a common figure number found at the beginning of each
new illustration throughout the manual.
1. Each step throughout the entire manual has a check box to the
left of it. As you complete each step, mark the box with a check. If you
need to take a break and return to building at a later time you will be
able to locate the exact step where you left off.
*NOTE: This is a common note. It is used to call attention to
specific details of a certain step in the assembly.
IMPORTANT NOTE: Even if you are familiar with Team
Losi kits, be sure and pay attention to these notes. They point out
very important details during the assembly process. Do not ignore
these notes!
The Team Losi Icon designates a performance tip.
These tips are not necessary, but can improve the performance of
your XXX-NT AD2 truck.
In illustrations where it is important to note which
direction parts are pointing, a helmet like this one will be included in
the illustration. The helmet will always face the front of the car. Any
reference to the right or left side will relate to the direction of the
helmet.
KIT/MANUAL ORGANIZATION
This kit is composed of different bags marked A through I. Each bag
contains all of the parts necessary to complete a particular section of
the XXX-NT Adam Drake Edition 2 truck. Some of these bags have
subassembly bags within them. It is essential that you open only one
bag at a time and follow the correct sequence, otherwise you may face
difficulties in finding the right part. It is helpful to read through the
instructions for an entire bag prior to starting assembly. Key numbers
(in parentheses) have been assigned to each part and remain the same
throughout the manual. In some illustrations, parts which have al-
ready been installed are not shown so that the current steps can be
1. INTRODUCTION
XXX-NT ADAM DRAKE EDITION 2 COMPLETED KIT DIMENSIONS
Length: 16-1/2"
Front Width: 12-3/4"
Rear Width: 12-3/4"
Height: 5-1/4"
Wheel base: 11-1/4"
All dimensions at ride height.
Weight may vary
P/N: LOSA0846
i
illustrated more clearly.
For your convenience, an actual size hardware identification guide
is included with each step. To check a part, hold it against the silhou-
ette until the correct part is identified. In some cases extra hardware
has been supplied for parts that may be easy to lose.
The molded parts in this kit are manufactured to demanding toler-
ances. When screws are tightened to the point of being snug, the
parts are held firmly in place. For this reason it is very important that
screws not be overtightened in any of the plastic parts.
To insure that parts are not lost during construction, it is recom-
mended that you work over a towel or mat to prevent parts from rolling
away.
IMPORTANT SAFETY NOTES
1. Select an area for assembly that is away from the reach of small
children. The parts in the kit are small and can be swallowed by
children, causing choking and possible internal injury.
2. The shock fluid and greases supplied should be kept out of
children’s reach. They were not intended for human consumption!
3. Exercise care when using any hand tools, sharp instruments,
or power tools during construction.
4. Carefully read all manufacturer’s warnings and cautions for
any glues, fuel, or paints that may be used for assembly and operating
purposes.
5. Gas powered vehicles should not be operated indoors.
6. Be careful when handling your truck after it has been run for
any period of time. The engine and many parts can get extremely hot
during operation.
TOOLS REQUIRED
Team Losi has supplied all Allen wrenches and two special wrench s
that are needed for assembly and adjustments. The following com-
mon tools will also be required: Small flatblade screwdriver, Phillips
screwdriver, needle nose pliers, regular pliers, scissors, or other body
cutting/trimming tools. 3/16", 1/4", 5/16", and 3/8" nut drivers are op-
tional.
Содержание XXX-NT AD2
Страница 65: ......
