TE Connectivity SGI 1.25, Спецификация приложения

Страница: 10 / 22

114-106497
Rev 5
10 of 22
WIRE SIZE CONTACT 2371403-1, 2454997-1
mm 2 AWG
WIRE BARREL CRIMP
INSULATION
BARREL CRIMP
WIDTH
INSULATION
BARREL
CRIMP HEIGHT
WIRE BRUSH REAR BELLMOUTH
HEIGHT
±0.03
WIDTH APPLICATOR APPLICATOR
0.128 26 0.51 1.0 max
(0.84 Crimper
Width)
F shape
1.0 max.
(0.84 Crimper
Width)
F shape
(1) As required 0.0 - 0.45 0.15-0.35
0.0804 28 0.46
0.0507 (2) 30 0.41
WIRE SIZE CONTACT 2371403-2, 2454997-2
mm 2 AWG
WIRE BARREL CRIMP
INSULATION
BARREL CRIMP
WIDTH
INSULATION
BARREL
CRIMP HEIGHT
WIRE BRUSH REAR BELLMOUTH
HEIGHT
±0.03
WIDTH APPLICATOR APPLICATOR
0.205 24 0.68
1.2 max
(0.95 Crimper
Width)
F shape
1.2 max.
(1.05 Crimper
Width)
F shape
1.60 +/-0.05 0.0 - 0.45 0.15-0.35
0.128 26 0.60
0.0804 (2) 28 0.56
WIRE SIZE CONTACT 2371403-3, 2454997-3
mm 2 AWG
WIRE BARREL CRIMP
INSULATION
BARREL CRIMP
WIDTH
INSULATION
BARREL
CRIMP HEIGHT
WIRE BRUSH REAR BELLMOUTH
HEIGHT
±0.03
WIDTH APPLICATOR APPLICATOR
0.205 24 0.68 1.2 max
(0.95 Crimper
Width)
F shape
1.2 max.
(0.95 Crimper
Width)
F shape
(3) 1.4 ~ 1.8 0.0 - 0.45 0.15-0.35
0.128 26 0.60
0.0804 (2) 28 0.56
CONTACT 2428106-1
mm 2 AWG
WIRE BARREL CRIMP
INSULATION
BARREL CRIMP
WIDTH
INSULATION
BARREL
CRIMP HEIGHT
WIRE BRUSH REAR BELLMOUTH
HEIGHT
±0.03
WIDTH APPLICATOR APPLICATOR
0.128 26 0.51 1.0 max
(0.84 Crimper
Width)
F shape
1.0 max.
(0.84 Crimper
Width)
F shape
(1) As required 0.0 - 0.45 0.15-0.35
0.0804 28 0.46
0.0507 (2) 30 0.41
* Note:
(1) Insulation crimp height will be variable depending on insulation diameter.
(2) Slight touch bottom is acceptable for 2371403-1 / 2454997-1 / 2428106-1 with 30AWG wire and 2371403-2
/ 2454997-2 / 2371403-3 / 2454997-3 with 28AWG wire.
(3) Insulation crimp height for 2371403-3 / 2454997-3 will be variable in 1.4~1.8mm depending on insulation
diameter.
Figure 4
L. Straightness
The force applied during crimping may cause some bending between the crimped wire barrel and the mating
portion of the contact. Such deformation is acceptable within the following limits:
The side-to-side bending of the contact may not exceed the limits provided in Figure 5.
The crimped contact, including cutoff tab and burr, shall not be bent above or below the datum line more than
the amount given in Figure 5.