background image

Application Specification 

of 22 

© 2023 TE Connectivity Ltd. family of companies. 
All Rights Reserved. 
*Trademark  

TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks.  Other logos, product, and/or company names may be trademarks of their respective owners. 

PRODUCT INFORMATION 1-800-522-6752 

This controlled document is subject to change. 
For latest revision and Regional Customer Service, 
visit our website a

www.te.com

114-106497 

13 DEC 23  

Rev 5

NOTE 

All numerical values are in metric units [with U.S. customary units in brackets]. Dimensions are in millimeters [and inches]. 
Unless otherwise specified, dimensions have a tolerance of ±0.13 [±.005] and angles have a tolerance of ±2°. Figures and 
illustrations are for identification only and are not drawn to scale.

 

 

1.

 

INTRODUCTION 

This specification covers the requirements for application of Signal Grace Inertial (SGI) 1.25 & 1.50 connector 
system includes SMT header assembly and plug assembly used in the wire-to-board interconnections, cap 
assembly and plug assembly used in the wire-to-wire interconnections. 

The SGI 1.25 connector system is available in 2 through 18 positions for single row, 20/22/30/40 positions for 
dual row, and SGI 1.50 connector system is available in 2 through 12 positions for single row, 4 through 18 
positions for dual row. Wire size ranges from 26 to 30 AWG for 1.25mm pitch connector, and 24 to 28 AWG for 
1.50mm pitch connector. 

When corresponding with TE Connectivity Personnel, use the terminology provided in this specification to 
facilitate your inquiries for information. Basic terms and features of this product are provided in Figure 1. 

 

 

SGI 1.25 Single Row 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 
SGI 1.25 & 1.50 Connector System 

Header Assembly  
SGI 1.25 Single Row (5pos shown) 

Plug Housing 
SGI 1.25 Single Row (5pos shown) 

Locking Latch 

Mating Face 

Mating Face 

Wire Cavity 

Cap Housing 
SGI 1.25 Single Row (10pos shown) 

Mating Face 

PRELIMINARY

Содержание SGI 1.25























Отзывы: