TDK-Lambda GENESYS GEN 2400W Series, Техническое руководство

Страница: 75 / 88

83-517-000 Rev. A
65
NOTES:
1. In
“
Advanced Parallel
” mode (refer to Section 5.15.2), “
n
” is the total system Output current.
2. In
“
Advanced Parallel
” mode, “
MC?
” returns the Master unit Output current multiplied by the “Number of
Slave units + 1
”.
Global Output Commands 7.7.6
7.7.6.1 General
All power supplies, even if not the currently addressed power supply, receiving a Global command will execute
that Global command. No response (to the controller/PC issuing the command) will be returned to the
controller/PC. The controller/PC issuing the Global command will be responsible to delay any other
communications until the command is executed. The suggested delay is 200 milliseconds minimum.
If the Global command contains an error,
“out of range values” for example, no error report will be sent to the
issuing controller/PC.
# Command Description
1 GRST Global Reset . Brings the power supply to a safe and known state:
Output voltage : 0V, Output current : 0A, OUT : Off , Local/Remote : Remote, AST :
OFF, OVP : Maximum, UVL : 0V.
The conditional register ( FLT and STAT ) are updated. Other registers are not
changed.
Non-latching faults (FB, OVP, SO) are cleared,
OUT fault stays
2 GPV n Sets the Output voltage value in Volts. The range of Output voltage values is shown in
Table 7-
3. ‘
n
’ may be up to 12 characters plus decimal point
3 GPC n Program the Output current value in Amperes. The range of Output current values is
shown in Table 7-
4. ‘
n
’ may be up to 12 characters plus decimal point
4 GOUT
Turns the output to ON or OFF :
“
OUT 1 (or OUT ON)
” = Turn Output
ON
“
OUT 0 (or OUT OFF)
” = Turn Output
OFF ; clears CV and CC bits in the Status
Condition ( STAT ) register.
OUT ON
will respond with “
E07
” if the output cannot be turned
ON because of a
latching fault (OTP, AC, ENA, SO) shutdown.
5 GSAV
Saves
“Present Settings”. Same settings as power-down last settings listed in Section
5.13 except the unit Address and Baud rate are not saved to EPROM memory. These
settings are erased when the power supply AC Input power is switched OFF and the
new ‘Last Settings“ are saved.
6 GRCL Recall
s “Last Settings”. Settings are from last AC Input power-down or from last ‘
SAV
’
or ‘
GSAV
’ command. Unit Address and Baud rate are not recalled so serial
communication is not interrupted.
Model
VOrated
Minimum
(V)
Maximum
(V)
Model
IOrated
Minimum
(A)
Maximum
(A)
8 0.0000 8.000 300 000.00 300.00
10 00.000 10.000 240 000.00 240.00
16
00.000 16.000
150
000.00 150.00
20
00.000 20.000
120
000.00 120.00
30 00.000 30.000 80 00.000 80.000
40 00.000 40.000 60 00.000 60.000
60 00.000 60.000 40 00.000 40.000
80 00.000 80.000 30 00.000 30.000
100 000.00 100.00 24 00.000 24.000
150 000.00 150.00 16 00.000 16.000
300 000.00 300.00 8 0.0000 8.0000
600 000.00 600.00 4 0.0000 4.0000
Table 7-3: Voltage programming range Table 7-4: Current programming range