1-3
1-3
THDC / THDCP - 954 / 955 / 974 (Rev. 06/03)
THDC / THDCP - 954 / 955 / 974 (Rev. 06/03)
Illust
Illustration 1-
ration 1-3.
3. Fan Dri
Fan Drive Belt
ve Belt
ADJUSTING
ADJUSTING
SCREW LOCKNUT
SCREW LOCKNUT
ADJUSTMENT
ADJUSTMENT
LINK LOCKING
LINK LOCKING
CAPSCREW
CAPSCREW
PIVOT CAPSCREW
PIVOT CAPSCREW
AND NUT
AND NUT
Illustr
Illustration 1-4.
ation 1-4. Alternator D
Alternator Drive Belt
rive Belt
Fan Drive Belt Tension
Fan Drive Belt Tension
(Illustration 1-3)
(Illustration 1-3)
..
The
The
tension of the fan drive belt should be 200 - 240
tension of the fan drive belt should be 200 - 240
ft-lbs (890 - 1070 N
ft-lbs (890 - 1070 N
⋅⋅
m) for a used belt and 300
m) for a used belt and 300
ft-lbs (1330 N
ft-lbs (1330 N
⋅⋅
m) for a new belt. A belt is consid-
m) for a new belt. A belt is consid-
ered used if it has been in operation for 10 min-
ered used if it has been in operation for 10 min-
utes or longer
utes or longer.
. If the used belt tensi
If the used belt tension is less than
on is less than
the minimum tension value, tighten the belt to the
the minimum tension value, tighten the belt to the
maxim
maximum tension value.
um tension value. T
To obtain the proper belt
o obtain the proper belt
tension value, use an appropriate belt tension
tension value, use an appropriate belt tension
gauge.
gauge. Perform
Perform the follow
the following procedur
ing procedures to
es to
adjust the tension of the belt.
adjust the tension of the belt.
CAUTION:
CAUTION:
Do not adjust belt tension to
Do not adjust belt tension to
the maximum value with the adjusting screw.
the maximum value with the adjusting screw.
Belt tension can increase when the locknut is
Belt tension can increase when the locknut is
tightened and cause reduced belt and bearing
tightened and cause reduced belt and bearing
life.
life.
1.
1. Loos
Loosen the idle
en the idler pull
r pulley shaf
ey shaft lock
t locknut.
nut.
2.
2. Adju
Adjust the bel
st the belt to the cor
t to the correc
rect tensi
t tension by turn
on by turning
ing
the adjusting screw clockwise until the proper
the adjusting screw clockwise until the proper
belt tension is obtained (see
belt tension is obtained (see
Caution
Caution
above).
above).
3.
3. T
Tight
ighten the idl
en the idler pull
er pulley shaf
ey shaft lock
t locknut to a
nut to a
torque value of 140 ft-lbs (190 N
torque value of 140 ft-lbs (190 N
⋅⋅
m).
m).
4.
4. Chec
Check the belt t
k the belt tensi
ension again to m
on again to make sur
ake sure the
e the
belt is adjusted to the correct value.
belt is adjusted to the correct value.
Alternator Drive Belt Tension
Alternator Drive Belt Tension
(Illustration 1-4)
(Illustration 1-4)
..
The tension of the alternator drive belt should be
The tension of the alternator drive belt should be
60 - 120 ft-lbs (270 - 530 N
60 - 120 ft-lbs (270 - 530 N
⋅⋅
m) for a used belt and
m) for a used belt and
150 ft-lbs (670 N
150 ft-lbs (670 N
⋅⋅
m) for a new be
m) for a new belt.
lt. A belt is c
A belt is con-
on-
sidered used if it has been in operation for 10 min-
sidered used if it has been in operation for 10 min-
utes or longer
utes or longer.
. If the used belt tensi
If the used belt tension is less than
on is less than
the minimum tension value, tighten the belt to the
the minimum tension value, tighten the belt to the
maxim
maximum tension value.
um tension value. T
To obtain the proper belt
o obtain the proper belt
tension value, use an appropriate belt tension
tension value, use an appropriate belt tension
gauge.
gauge. Perform
Perform the follow
the following procedur
ing procedures to
es to
adjust the tension of the belt:
adjust the tension of the belt:
1.
1. Loos
Loosen the adj
en the adjusti
usting scr
ng screw loc
ew locknut
knut..
2.
2. Loosen the adj
Loosen the adjustment
ustment link l
link locking c
ocking capscrew
apscrew..
3.
3. Loos
Loosen the pi
en the pivot c
vot capsc
apscrew
rew and nut
and nut..
4.
4. Adjus
Adjust the belt to th
t the belt to the corr
e correct te
ect tensio
nsion by turni
n by turning
ng
the adjusting screw clockwise until the proper
the adjusting screw clockwise until the proper
belt tension is obtained.
belt tension is obtained.
5.
5. Ti
Tighten the
ghten the adjusting
adjusting screw
screw locknut
locknut against
against
the retainer.
the retainer.
6.
6. Ti
Tighten the adj
ghten the adjustment
ustment link l
link locking c
ocking capscrew
apscrew
to a
to a torq
torque value of 60
ue value of 60 ft-
ft-lbs (80 N
lbs (80 N
⋅⋅
m).
m).
7.
7. T
Tight
ighten the piv
en the pivot caps
ot capscrew a
crew and nut to a torqu
nd nut to a torque
e
value of 35 ft-lbs (47 N
value of 35 ft-lbs (47 N
⋅⋅
m).
m).
Engine Cleaning.
Engine Cleaning.
The engine must be steam
The engine must be steam
cleaned every 6 months or 1500 hours, whichever
cleaned every 6 months or 1500 hours, whichever
https://www.forkliftpdfmanuals.com/
Содержание THDC-954
