manualshive.com logo in svg

Taylor-Dunn Bigfoot, Руководство оператора

Поделиться
Скачать
Taylor-Dunn Bigfoot Скачать руководство пользователя страница 21

Page 21

B5-440-36 / B5-440-48 / B5-540-48XL / BF-030-48Operator Manual 

MB-440-07

Emergency Power Cut Switch

The Emergency Power Cut Switch should be used if the vehicle starts to operate in an unexpected 
manner or if there is an odor or sound that may indicate an overloaded electrical circuit. If any of 
the above occurs, immediately and safely pull to the side of the road and stop. Then push on the 
switch knob and exit the vehicle. Do not reengage the switch until the vehicle has been inspected 

by a qualified technician.

The Emergency Power Cut Switch should only be activated if the vehicle must be stopped. Do not 
use the switch when only parking the vehicle.

The location of the switch will vary depending on vehicle configuration. The 

switch is a large red knob located within reach of the driver. See the illustration 
to the right for a typical power cut switch knob.

Pull up on the knob to reengage 

Park Brake, Manual (Standard on 
BIGFOOT Models)

The park brake is actuated with a hand lever. 
To set the park brake, push down on the brake 

pedal and pull the lever back firmly. To release 

the park brake, press the foot brake pedal, push 
the button on the end of the handle, then push 
the handle forward and downward until it stops.

Park Brake, Automatic Electric 

The automatic electric park brake is standard on BIGFOOT XL and optional on the BIGFOOT.

The automatic electric park brake will be applied whenever the vehicle is not in motion. While 
coasting or using the foot brake, the motor speed control monitors the motor rpm, the park brake 
will be applied after the motor stops rotating.

The automatic electric park brake will be applied when the driver gets up off the driver’s seat. If 
the driver gets off the seat while the vehicle is in motion, the vehicle will rapidly decelerate and 
then apply the park brake.

Refer to 

Towing This Vehicle

 for information on temporarily disabling the automatic electric park 

brake. 

The park brake should be disabled for servicing or towing procedures only.  Do not operate 
the vehicle while the automatic park brake is disabled. Operating the vehicle with the 
automatic park brake disabled could lead to severe bodily injury and/or property damage.

WARNING

Содержание Bigfoot

















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды