manualshive.com logo in svg

TANDBERG SLR7, Справочное руководство, Страница: 69 / 118

Поделиться
Скачать
TANDBERG SLR7 Скачать руководство пользователя страница 69

__________________________________________________________________________

Tandberg SLR Reference Manual

8-1

8.

Hardware Interface

8.1. Power Interface

Power for the Drive is provided through a 4-pin connector. The connector type is AMP

174804-1 or equivalent. The same type is used as power connectors for 5.25-inch diskette

drives and 5.25-inch fixed disk drives.

8.2. Definition of Terms

The following terms are widely used:

Term

Description

Asserted Signal

A signal which is driven to the logical 1 state. In this
document an asserted signal is always shown in “high

level”.

Bus Device

A host computer or peripheral CONTROLLER which

can be attached to the SCSI-bus.

CDB

Command Descriptor Block.

Connect (Select)

This function occurs when an INITIATOR selects a
TARGET to start an operation.

Controller

A SCSI-BUS DEVICE (a typical TARGET) which con-

trols one or more PERIPHERAL DEVICES.

Deasserted Signal

A signal which is driven to the logical-0 state.

Disconnect

This function occurs when a TARGET releases control

of the SCSI-bus, allowing the bus to become free.

Initiator

A BUS DEVICE which requests an operation to be

performed by another BUS DEVICE.

LUN

Logical Unit Number within a device.

Peripheral Device

An I/O Device such as a disk, printer or streaming

tape unit.

Reconnect

This function occurs when a TARGET selects (Rese-
lect) an INITIATOR to continue an operation after a

DISCONNECT.

Target

A BUS DEVICE which performs an operation reque-
sted by an INITIATOR.

Table 8.1  Definition of Terms

Содержание SLR7























































































































Отзывы:

Нет отзывов