TANDBERG SLR7 Скачать руководство пользователя страница 21

Страница: 21 / 118

Tandberg Data

Product Specifications

___________________________________________________________________________

Tandberg SLR Reference Manual

3-3

3.3.2. Temperature Variation

Operating

Maximum 10°C per hour, non-condensing

3.3.3. Atmospheric Pressure

Operating

53 - 106 kpa [maximum altitude 4 000 m (13 000 ft)]

Storage

15 - 106 kpa [maximum altitude 12 200 m (40 000 ft)]

Transport

15 - 106 kpa [maximum altitude 12 200 m (40 000 ft)]

3.3.4. Vibration

Test Method

IEC-68-2-6 sine sweep

IEC-68-2-64 random sweep

Frequency Profile (Hz)

Acceleration (G)

Peak Displacement (mm)

Storage Mode

- 58

58 - 500

2.0

0.150 ±10 %

Transport Mode

5 - 12
12 - 500

2.0

3.5 ±10 %

Frequency Profile (Hz)

Acceleration (G)

Operating Mode

Sine Sweep

5 - 100

150 - 500

0.5

0.1

Frequency Profile (Hz)

PSD Level (g

/Hz)

(NOTE 1)

Operating Mode
Random Sweep

(NOTE 2)

17 - 45

48 - 62
65

150
200 - 500

2.0

⋅

-5

1.1

⋅

-3

8.0

⋅

-3

1.0

⋅

-3

5.0

⋅

-5

1.0

⋅

-5

NOTE 1:

PSD = Power Spectral Density

NOTE 2:

Individual Drives may experience a capacity loss of up to 10% if exposed to the extreme of the random

vibration specification for the whole duration of the write operation. There is no degradation in data
integrity.

3.3.5. Impact and Shock

Shock

Transport

Lifted 1.0 m for “single-pack” and 0.6 m for “10-pack”, and allowed to fall freely on to a hard,

rigid surface Fall sequence includes all 6 sides and the most critical edge and corner. (ASTM

D 5276-94).

Shock
Storage

490 m/s

(50 g), Half sinewave, 11 ms duration. (IEC-68-2-27).

Shock

Operating

49 m/s

(5 g), Half sinewave, 11 ms duration.

Содержание SLR7























































































































Результаты поиска

Содержание SLR7

Отзывы:

TANDBERG SLR7, Справочное руководство, Страница: 21 / 118

Результаты поиска

Содержание SLR7

Отзывы: