TANDBERG SLR7 Скачать руководство пользователя страница 24

Страница: 24 / 118

Tandberg Data

Product Specifications

___________________________________________________________________________

3-6

Tandberg SLR Reference Manual

3.5. Product Reliability

The predicted reliability of the Drive is expressed in two parts that will cover the expected

random Mean Time Between Failures (MTBF) for the electronics based on the Power On

Hours (POH) and the Mean Time to Failure (MTTF) for the mechanical parts based on the

POH

and

the Duty Cycle.

3.5.1. Electronics MTBF

Predicted, Actual

“Mature” MTBF

> 300 000 POH

Important Notice!
The MTBF value is dependent of correct handling (f. ex.: ESD protective measures are used),
installation and use of the Drive by the system installer/designer.

3.5.2. Mechanics MTTF

The failure rate for these parts is related to how often the Drive is actually used. In the case of

the most critical components which are the head and the capstan motor, the reliability is

specified as the Mean Time to Failure (MTTF) based on the POH and the Duty Cycle. The

MTTF-values are not accumulative as the wear takes place in parallel.

Capstan Motor
Life Time

> 10 000 Run Hours (see NOTE)

NOTE:

Streaming operation, NOT extensive start/stop operations.

Cartridge
Load/Eject

> 30 000 load/ejects

Tandberg SLR7 is specified for > 10 000 load/ejects

3.5.3. Useful Life Cycle

This is the period during which the Drive is serviceable either by adjustment or replacement of

defective parts. In the case of the mechanical parts, replacements must be expected as soon

as the life-time is approached (see 3.5.2). This will depend on the actual usage of the Drive in

each case.

Useful Life Cycle

> 10 years

Содержание SLR7























































































































Результаты поиска

Содержание SLR7

Отзывы:

TANDBERG SLR7, Справочное руководство, Страница: 24 / 118

Результаты поиска

Содержание SLR7

Отзывы: