Tanco Autowrap - 1310 / 1320
Operator’s Manual
37
Loading
Set the machine height with the tractor lift arms so there is approximately 300mm clearance between the rollers and the ground. It is very important that the rollers do not hit the ground
when loading as this can damage the rollers and overload the roller drive. Open the rollers to the maximum. Drive in under the bale. Close the rollers fully to lift the bale clear of the
ground. See Controller Information for setting controller for automatic one touch loading. To ensure that the bale does not creep off the rollers while wrapping it is important that the
rollers are inclined towards the tractor, the machine may need to be raised to achieve this.
Start Wrapping
Because of the unique folding design of the 1320 wrapping arm it is easier to operate the wrapping pro¬cess in automatic A mode rather than in M manual. The comments in brackets
below are the program¬mable factors on the controller that govern the function that is happening.
The folded wrapping arms should be parked in the centre of the chassis before commencing the auto¬matic wrapping sequence.
The film cutter releases the ends of the films (after, Wraps to Release).
Note the controller counts in steps of 2, because for each revolution of the wrapping arm two wraps of film are applied.
On the last revolution of the wrapping sequence the arm steps down to slow speed (after Delay to Slow time past the sensor).
The wrapping arm folds the dispensers together (after Delay to Fold time).
The cutter opens.
The two dispensers rotate together past the opened cutter (for Delay to Stop time).
The cutter closes (for C&S Close Time 2)
The wrapping arm reverses to the centre of the machine (for Reverse Time)
The bale is now ready for unloading.
Unloading
As with loading make sure that the rollers do not touch the ground when unloading.
Storage Place
At the storage place the bales should be placed systematically. Start at the right-hand side, and stack to the left. The machine is lowered, but not all the way down to the ground. The
rollers must not hit the ground. Push the “rollers out” button to open the rollers and drop the bale to the ground. Drive the trac¬tor carefully away from the bale. Try to avoid touching the
bale with the rollers. Place the next bale to the left of the first one so that the loose film end on the last bale will be locked. To be sure we recommend that you check that the film ends are
securely fastened, and eventually fasten them a little bit better when you have stacked the bales.
If the machine is front mounted, the bales can be staked upon each other.
9. OPERATIONAL FEATURES
Содержание 1300 Series
