5-36
MAINTENANCE
the machine or work bench, use the
steps, handrails or work bench to
support your body. Your weight should
be evenly distributed among the three
contact points (one hand and two feet
or two hands and one foot).
• Do not stand on the dozer blade and
perform maintenance work. Doing so is
dangerous because of the unsteady
foothold. Use the work bench.
Inspection
IMPORTANT: Check the fluid level of all
cells following the steps below, even
when the fluid level can be checked using
the indicator.
1. Open the left side cover.
EVERY 50 HOURS
INSPECTING THE BATTERY FLUID LEVEL
AND REPLENISHING
• Do not use the battery when the fluid
level is below the lower level limit. Doing
so will hasten the deterioration of the
internal portions of the battery and
shorten the battery life. It also can
cause rupturing (explosion).
• Batteries generate flammable hydrogen
gas which may explode. Keep away
from flame, sparks, fire or lighted
cigarettes.
• Use a dampened cloth to clean above
the fluid level line and check the fluid
level. Do not clean with a dry cloth;
otherwise it can cause static electricity
to build up, resulting in ignition or
explosion.
• Wear protective goggle and clothing
when working with batteries.
• Do not add the distilled water above the
upper level limit. Doing so could cause
the fluid to leak. This fluid can cause
skin damage if contacted, or can cause
the machine components to corrode.
• Batteries contain sulfuric acid which will
damage eyes or skin if contacted.
· If eye contact occurs, flush
immediately with clean water and get
prompt medical attention.
· If accidentally swallowed, drink large
quantities of water or milk and call a
physician immediately.
· If acid contacts skin or clothing, wash
off immediately with a lot of water.
• Before performing maintenance on top
of the work bench, clean the footing and
observe the following precautions to
prevent falling.
· Do not spill oil or grease.
· Do not leave tools scattered around.
· Watch your step when walking.
• Never jump down from the machine or
the work bench. When getting on or off
2. Inspect the indicator (1).
· Blue: Charging complete
· White: OK
· Red/center White: Insufficient battery
fluid
· Red/center Red: Charging needed
3. Inspect the fluid level.
The fluid level must be between the upper
level (H) line and lower level (L) line. If not,
add distilled water up to the line (H).
Содержание TB1160W
