Tait TB8100 Скачать руководство пользователя страница 12

 

Page 12 of 20

TN-906-AN

© Tait Electronics Limited 21 December 2005

5.

In the 

Connect response

 field, enter 1.

6.

In the 

Disconnect command

 field, enter ^Mxxx^M/X^M.

This means:

7.

In the 

Disconnect response

 field, enter 3.

8.

In the 

Connection timing

 area, we recommend the following 

settings:

Set the number of retries to 20, the maximum allowed.

Set the time between retries to 60s for the first base station, and 
increment in steps of 5s for other base stations (e.g. set base station 
2 to 65s, base station 3 to 70s, etc.).  This prevents all base stations 
from retrying at the same time if a fault occurs that affects them all.

Set the minimum interval to at least 30 minutes.  The interval 
should be long enough to allow all base stations to dial out if 
necessary;  we suggest 30 minutes plus an extra 3 minutes for each 
base station on the site.

Note

If there is a particular condition that can be guaranteed to affect all 
base stations (e.g. mains failure), we recommend that you enable 
this alarm on only two base stations.  This precaution will prevent 
a mass dial-out attempt, but will still allow you to check for false 
alarms.

^M

instructs the APS to enter command mode

xxx

three instances of the logoff character

a

a. This must match the logoff character chosen when setting up the modem (L 

was chosen in this case).  Refer to 

“Common Configuration for all Ports” on 

page 14

.

^M

terminates the sequence

/X^M

exits command mode

Содержание TB8100





















Отзывы: