manualshive.com logo in svg

Tadpole SPARCbook 3 series, Справочное руководство

Поделиться
Скачать
Tadpole SPARCbook 3 series Скачать руководство пользователя страница 49

Memory Map and Interrupts

3-5

Interrupts

3.1.2

DRAM

The DRAM address multiplexers support SIMM units with up to 11 x 11 or 
(12 x 10) Row/Column multiplex (1Mbit, 4Mbit, and most 16Mbit 
devices). Each SIMM module can contain one or two banks of memory. 
SIMM sizes up to 64Mbytes are supported, with a maximum of 32Mbytes 
per bank.

The memory maps for the different configurations are based on the 
principle that the individual bank selects (RAS signals) are derived from 
the address decodes for fixed 32Mbyte memory segments.

Table 3-8 summarizes the possible memory implementations when using 
identical SIMM pairs.

*Figures in the Organization column can be either by 33 or by 36.

3.2

Interrupts

Interrupts from devices within SPARCbook 3 are signaled to the 
microSPARC as a 4-bit priority encoded value on S_IRL(3:0). Control of 
interrupts and prioritization is carried out by the SLAVIO. The 
microSPARC provides a structure of traps which supports fifteen external 
interrupts.

The SLAVIO contains interrupt control and mask registers which are used 
to enable and clear hardware interrupts from devices within the 
SPARCbook 3 system as well as interrupts from devices internal to the 
SLAVIO and MACIO. The SLAVIO also provides software generated 
interrupts on each of fifteen levels.

System

Capacity

SIMMs

Address Map

(Where memory appears)

Qty Organization*

Architecture of 

Each

16Mbytes

2

2M by 33

Two banks of 4Mbit

At 0 & 32Mbytes for 8Mbytes each

32Mbytes

2

4M by 33

One bank of 16Mbit

At 0 for 32Mbytes

64Mbytes

2

8M by 33

Two banks of 16Mbit

At 0 for 64Mbytes

128 Mbytes

2

16M by 33

Table 3-5  DRAM Mapping 

S3GX_TRMBook  Page 5  Friday, September 19, 1997  11:39 am

Содержание SPARCbook 3 series

























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды