Tadiran Telecom TGW4 SERIES Скачать руководство пользователя страница 83

Страница: 83 / 142

TGW4/8 Gateway Series for Aeonix User Configuration Manual

Tadiran Telecom (TTL) L.P. 71

2.8 Status

2.8.1 Call Status Verification

For each FXS phone and FXO trunk in the TGW gateway, you need to verify that it is registered in the

status of the Gateway.

After login, click the

Call Status

tab to open this interface.

Figure 2-37

Call Status Interface

Table 2-31

Parameters of call state

Title

Explanation

Registration

There are some types of Registration status:

Registered, Not registered, Fail, Server not response.

Line

There are six types of line status, On-hook, Off-hook, Ringing, Maintenance, Disconnect,
Parallel line in-use

Call

The call state includes Idle, Outpulsing, Ring, Entering number, In progress, Ring back, Talk,
Near end hung up, Far end hung up, and Timeout.

Phone No.

(Other End)

The number of the other party

Duration

Call duration

Operation

You can view call details such as local port and codec after the call is answered.

Incoming call count

Out

Outgoing call count

Answered

Answered call count

Содержание TGW4 SERIES















































































































































Результаты поиска

Содержание TGW4 SERIES

Отзывы:

Бренды по названию

Популярные бренды

Tadiran Telecom TGW4 SERIES, Руководство по настройке пользователя

Результаты поиска

Содержание TGW4 SERIES

Отзывы:

Бренды по названию

Популярные бренды