Tadiran Telecom TGW4 SERIES Скачать руководство пользователя страница 20

Страница: 20 / 142

User Configuration Manual TGW4/8 Gateway Series for Aeonix

8 Tadiran Telecom (TTL) L.P.

Table 1-10

Indicator Status of TGW8-2G and TGW8S-2G



Flashing indicator - A signal that flashes at a fast rate of on/off pulses.



Blinking indicator - A signal that flashes at a slow rate of on/off pulses.

Indicator

Status

Description

PWR (green)

Flashing green

The TGW is starting.

Steady green

The TGW is running.

Off

The TGW is powered off or a power supply fault occurs.

STU

(red, green)

Steady red

The WAN interface does not acquire the IP address. Possible

reasons: the WAN interface is not connected to a network cable,

the WAN interface address fails to be acquired by using DHCP,

the IP addresses are conflicted, and the PPPoE dialing fails.

Flashing red

The TGW is starting or the Kupdate is upgrading.

Steady green

Registration is successful.

Blinking

alternatively

between red and

green

Registration failed.

Flashing green

Calling.

Off

Registration has not started.

WAN

(green)

Steady green

A WAN connection is established without any service flow.

Flashing green

A WAN connection is established with service flow.

Off

WAN interface is disconnected.

AUX

(green)

Steady green

A link is connected without any service flow.

Flashing green

A service flow is being transmitted on the link

Off

A link is not connected.

VOICE

(Green-FXS,

yellow-FXO)

Indicates line type and TGW status:

Flashing yellow

The TGW is starting and the port is an FXO port.

Flashing green

The TGW is starting and the port is an FXS port.

Off

No line is detected. Possible reasons: the voice interface card is

not inserted or the port is damaged.

Indicates running status:

Steady yellow

Calling in or out via an analog trunk.

Flashing yellow

Ringing on calling in for an analog trunk.

Steady green

Off-hook or call established.

Flashing green

Ringing on incoming call.

Off

The port is in idle status.

Note: The TGW starts up for approximate 30s to indicate line type, then indicates

running status.

Содержание TGW4 SERIES















































































































































Результаты поиска

Содержание TGW4 SERIES

Отзывы:

Бренды по названию

Популярные бренды

Tadiran Telecom TGW4 SERIES, Руководство по настройке пользователя

Результаты поиска

Содержание TGW4 SERIES

Отзывы:

Бренды по названию

Популярные бренды