Tadiran Telecom TGW4 SERIES Скачать руководство пользователя страница 141

Страница: 141 / 142

TGW4/8 Gateway Series for Aeonix High Availability Configuration Guide

Tadiran Telecom (TTL) L.P.

129

6.4.3 Configure OPTIONS and REGISTER Settings

In the load balancing mode, the following timers must be configured:

Step1

In the

OPTIONS request period

field,

enter

the interval between receiving the response (200) from the SIP

server to the previous OPTIONS and sending the next OPTIONS.

Step2

In the

OPTIONS request timeout

field,

enter the period since the sending of the last OPTIONS with no

response by the SIP server.

Step3

In the

REGISTER request timeout

field,

enter the period from the sending of the first REGISTER with no

response by the previous SIP server to the sending of REGISTER to the next SIP server.

Figure 6-32

Page to configure OPTIONS and REGISTER settings

Содержание TGW4 SERIES















































































































































Результаты поиска

Содержание TGW4 SERIES

Отзывы:

Бренды по названию

Популярные бренды

Tadiran Telecom TGW4 SERIES, Руководство по настройке пользователя

Результаты поиска

Содержание TGW4 SERIES

Отзывы:

Бренды по названию

Популярные бренды