Tadiran Telecom TGW4 SERIES Скачать руководство пользователя страница 56

Страница: 56 / 142

User Configuration Manual TGW4/8 Gateway Series for Aeonix

44 Tadiran Telecom (TTL) L.P.

2.6.2 Routing Table

After login, click the

Routing > Routing Table

tab to open the Routing table configuration interface.

* For Aeonix US ALARMS



In version 336.10 or lower, Echo Cancellation was not part of the GUI.

In order to disable the Echo Cancellation mechanism for port 2524, you
should add a Routing Map rule

IP 2524 CODEC PCMU/20/0

and for all

ports

IP X CODEC PCMU/20/0.

Figure 2-24

Routing Table Configuration Interface

Click

to open the illustrative interface for routing configuration.

The routing table with a capacity of 500 rules provides two functions, including number transformation

and call routing assignment.

The TGW will match a rule from top to bottom.



Rules must be filled out without any blank at the beginning of each line; otherwise, the data

cannot be validated even if the system prompts successful submittal.



The routing table is empty by default. The gateways will direct a call to the SIP proxy server

when there is no matched rule for the call.

Содержание TGW4 SERIES















































































































































Результаты поиска

Содержание TGW4 SERIES

Отзывы:

Бренды по названию

Популярные бренды

Tadiran Telecom TGW4 SERIES, Руководство по настройке пользователя

Результаты поиска

Содержание TGW4 SERIES

Отзывы:

Бренды по названию

Популярные бренды