Tadiran Telecom TGW4 SERIES Скачать руководство пользователя страница 16

Страница: 16 / 142

User Configuration Manual TGW4/8 Gateway Series for Aeonix

4 Tadiran Telecom (TTL) L.P.

Table 1-5

Indicator Status of TGW4S



Flashing indicator - A signal that flashes at a fast rate of on/off pulses



Blinking indicator - A signal that flashes at a slow rate of on/off pulses

Indicator

Status

Description

PWR (green)

Flashing green

The TGW is starting.

Steady green

The TGW is running.

Off

The TGW is powered off or a power supply fault occurs.

STU

(red, green)

Steady red

The WAN interface does not acquire the IP address.

Possible reasons:



WAN interface is not connected to a network cable



WAN interface address fails to be acquired by using

DHCP



IP addresses are conflicted



PPPoE dialing fails

Flashing red

The TGW is starting or the Kupdate is upgrading.

Steady green

Registration is successful.

Blinking

alternatively

between red and

green

Registration failed.

Flashing green

Calling.

Off

Registration has not started.

WAN

(green)

Steady green

A WAN connection is established without any service flow.

Flashing green

A WAN connection is established with service flow.

Off

WAN interface is disconnected.

(green)

Steady green

A link is connected without any service flow.

Flashing green

A service flow is being transmitted.

Off

A link is not connected.

FXS/FXO

(green)

Steady green

Off-hook or call established.

Flashing green

Ringing on incoming call.

Off

The port is in idle status.

FXO is not applicable in TGW4S

Содержание TGW4 SERIES















































































































































Результаты поиска

Содержание TGW4 SERIES

Отзывы:

Бренды по названию

Популярные бренды

Tadiran Telecom TGW4 SERIES, Руководство по настройке пользователя

Результаты поиска

Содержание TGW4 SERIES

Отзывы:

Бренды по названию

Популярные бренды