Taco 00e Series Скачать руководство пользователя страница 43

Страница: 43 / 56

-43-

18. MODBUS
18.1 Modbus Related Interface

Terminal Designation

Terminal Description

MODE

Can be used to reset network configuration.

LED2 / ACT

Indicates Ethernet activity or Modbus reception.

B/D-

RS-485 negative data signal for Modbus.

A/D+

RS-485 positive data signal for Modbus.

COM/0V

RS-485 common and analog input common (ground).

18.2 Modbus Topology

The VR Control is a Modbus lag, connected directly to a Modbus RTU network. Connection can be made in either daisy

chain style (if cabling allows such a connection) or a limited length passive tap. Schematic example is in Figure 6.

Figure 6: Example of Modbus network

Typically, only one Lead pump device is connected to the serial bus, and one or several lags are also connected to the

bus. Lags do not communicate with each other and will never transmit data without receiving a proper request from

the master device.

Up to 32 single load devices can be connected to one RS-485 Modbus system without using a repeater. As this module

is a 1/8 load device, up to 256 modules can be connected to the bus. Repeaters can be used to extend the maximum

transmission distance and increase device count if needed.

Lag 1

Lead Pump

Lag 2

Lag 3

Line

Termina

tion

Line

Termina

tion

Passive tap

Daisy chain

Содержание 00e Series

























































Результаты поиска

Содержание 00e Series

Отзывы:

Бренды по названию

Популярные бренды

Taco 00e Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание 00e Series

Отзывы:

Бренды по названию

Популярные бренды