FAAST 7100X
INSTALLATION AND MAINTENANCE INSTRUCTIONS
© Pertronic Industries Ltd
26
FAAST XS (7100X) Installation Guide Iss 1.0, 201606
GLOSSARY:
Key Terms:
Configure:
To set up a program or computer system for a particular application.
FAAST Fire Alarm Aspirating Sensing Technology®:
High sensitivity aspirating smoke detection system.
IP Address:
An Internet Protocol (IP) address is a numerical label that is assigned to devices participating in a computer
network utilizing the Internet Protocol for communication between its nodes.
PipeIQ®:
A software program designed to work with the FAAST unit for system configuration, monitoring and pipe design.
Web server:
A Web server is a computer program that delivers (serves) content. The device contains an integrated Web
server which is used to observe detector configuration and may be used to remotely monitor the system.
Document Colour Code Key:
When using this manual, apply the information which applies to the particular FAAST XS model being installed
SS Blue: Document Headers
Black:
applies to both 7200BPI and 7100X FAAST XS Series detector
Blue:
important settings to be configured on each 7100X Device
LASER SAFETY INFORMATION
WARRANTY
FCC STATEMENT
System Sensor warrants its enclosed smoke detector to be free from
defects in materials and workmanship under normal use and service for a
period of three years from date of manufacture. System Sensor makes no
other express warranty for this smoke detector. No agent, representative,
dealer, or employee of the Company has the authority to increase or alter
the obligations or limitations of this Warranty. The Company’s obligation of
this Warranty shall be limited to the repair or replacement of any part of the
smoke detector which is found to be defective in materials or workmanship
under normal use and service during the three year period commencing
with the date of manufacture.
After phoning System Sensor’s toll free number 800-SENSOR2 (736-7672)
for a Return Authorization number, send defective units postage prepaid
to: System Sensor, Returns Department, RA #__________, 3825 Ohio
Avenue, St. Charles, IL 60174.
Please include a note describing the malfunction and suspected cause of
failure. The Company shall not be obligated to repair or replace units
which are found to be defective because of damage, unreasonable use,
modifications, or alterations occurring after the date of manufacture.
In no case shall the Company be liable for any consequential or incidental
damages for breach of this or any other warranty, expressed or implied
whatsoever, even if the loss or damage is caused by the Company’s
negligence or fault Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation or exclusion
may not apply to you. This Warranty gives you specific legal rights, and
you may also have other rights which vary from state to state.
This aspiration detector does not produce any hazardous laser radiation
and is certified as a Class 1 laser product under the U.S. Department of
Health and Human Services (DHHS) Radiation Performance Standard
according to the Radiation Control for Health and Safety Act of 1968. Any
radiation emitted inside the smoke detector is completely within the
protective housings and external covers.
The laser beam cannot escape from the detector during any phase of
operation. The Center of Devices and Radiological Health (CDRH) of the
U.S. Food and Drug Administration implemented regulations for laser
products on August 2, 1976. These regulations apply to laser products
manufactured after August 1, 1976. Compliance is mandatory for products
marketed in the United States.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
