manualshive.com logo in svg

SynCardia Companion 2 Driver System, Руководство оператора

Поделиться
Скачать
SynCardia Companion 2 Driver System Скачать руководство пользователя страница 27

SynCardia Systems, LLC 
Companion 2 Driver System Operator Manual

 

 

Page 27 of 132 

6.4.2  Alarm and Power Status LED Array 

The  Driver  contains a redundant LED array  (

Figure 6-2

)  that 

communicates information about Alarm Status and Power Status in 
the event of a display screen failure.  

 

        

 

Figure 6-2 – Driver Alarm and Power Status LED Array  

 

The Alarm LED:  Solid green indicates there is no alarm.  Solid 
yellow, flashing yellow, red and flashing red all indicate alarms with 
each color indicating an alarm of different severity. 

External Power LED:  Solid green indicates external power is 
applied to the Driver.  A yellow external power LED  indicates the 
Driver is operating from battery power.  

Battery LED:   Solid green indicates the battery is charged and has 
at least 20% of capacity.  The LEDs flash green when the batteries 
are being charged.  A yellow Battery LED indicates the remaining 
capacity is low (less than 30 minutes).  A flashing yellow Battery 
LED indicates the remaining battery capacity is very low (less than 
10 minutes) or there is a battery fault condition.  

Emergency Battery  LED:  Solid  green  indicates the Emergency 
Battery  is not in use.  A flashing green emergency LED indicates 
the Emergency Battery is being charged.  Flashing red indicates a 
very high alarm state.  

 

 

Alarm Indicator 

External Power 

Indicator 

Emergency Battery 

Indicator 

External Battery 

Indicators 

Содержание Companion 2 Driver System







































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды