manualshive.com logo in svg

SynCardia Companion 2 Driver System, Руководство оператора

Поделиться
Скачать
SynCardia Companion 2 Driver System Скачать руководство пользователя страница 105

SynCardia Systems, LLC 
Companion 2 Driver System Operator Manual

 

 

Page 105 of 132 

Chapter  18.  Switching from Companion 2 Driver to Primary 

Freedom Driver  

NOTE:

 The procedure described below to switch drivers is the same for both the 

50cc TAH-t and 70cc TAH-t. 

 

 

CAUTION 

It is recommended to have two people switch from the Companion 2 
Driver to the Freedom Driver. 

Make sure all items and accessories are available before exchanging 
Drivers. 

 

18.1  Materials 

Prior to switching the patient from the Companion 2  Driver to the 
Freedom Driver System, the following must be available:

 

•

  One prepared primary Freedom Driver  

•

  One prepared backup Freedom Driver 

•

  Wire Cutter tool from the Freedom Patient Tool Kit 

•

  Driveline Retention Bag from the Freedom Tool Kit 

 

18.2  Preparation to Perform Switch from Companion 2 Driver to 

Freedom Driver 

Both primary and backup Freedom Drivers must be tested at the 
Hospital prior to use, following the checklist for the Freedom Driver 
Test Protocol in the Freedom Operator Manual. If any of the Drivers do 
not pass the Protocol, do not connect the patient to the Freedom Driver 
System and contact SynCardia immediately. 

To turn on the Freedom Driver: 

•

  Remove the driveline caps from the ends of the Freedom Driver 

Drivelines 

•

  Insert two charged Onboard Batteries into the Freedom Driver 

•

  Connect the Freedom Driver into a wall power outlet using the AC 

Power Supply and Cord  

•

  Verify that the Freedom Driver starts (you should hear the working 

motor inside of the Driver and feel air coming out of the Drivelines)  

NOTE: 

The Freedom Driver is set up not to activate a Fault Alarm for 

low Cardiac Output for 15 minutes after it has been initially turned on, 
to allow time to connect to a TAH-t. 

Содержание Companion 2 Driver System







































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды