Sutter Instrument Lambda DG-4 Скачать руководство пользователя

Страница: 73 / 86

LAMBDA DG-4 & DG-5 OPERATION MANUAL – REV.

3.05C

(

20150414

)

APPENDIX B.

ACCESSORIES

B.1.

Liquid Light Guides and Other Accessories

LLG

Liquid light guide (2 meters, 3mm diameter), C-mount, lens and lens tube

LLG/380

Liquid light guide (2 meters, 3mm diameter), C-mount, lens, and lens tube. Allows
light input into near IR.

B.2.

Microscope Mounting Adapters

Mounting adapters for Nikon, Zeiss, Leica and Olympus microscopes are available. Please

refer to the Microscope Adapters section of Sutter Instrument’s web site

(

) for further information.

B.3.

Xenon Arc Lamp Bulbs

The bulbs listed in the following do not include the outer blue housing. If an extra housing is

required, please contact Sutter Instrument by phone, fax, or email.

O661176

Ozone free 175 Watt xenon bulb (attenuated output below 340nm)

O661175

Full spectrum 175Watt xenon bulb

O661301

Ozone free 300 Watt xenon bulb (attenuated output below 340nm)

O661300

Full spectrum 300 Watt xenon bulb

O661115

Housing and heat sink for bulb (bulb is installed when ordered at the same time as

the housing)

WARNING: Full-spectrum bulbs produce ozone, which is toxic

and must be eliminated from the area in which the Lambda DG-4/5

operates. Please be certain that you have proper ventilation – systems

installed with full-spectrum bulbs must be connected to an ozone-

removing device or system. Contact Sutter Instrument for more

information.

Содержание Lambda DG-4























































































Результаты поиска

Содержание Lambda DG-4

Отзывы:

Похожие инструкции для Lambda DG-4

Бренды по названию

Популярные бренды

Sutter Instrument Lambda DG-4, Руководство по эксплуатации

Результаты поиска

Содержание Lambda DG-4

Отзывы:

Похожие инструкции для Lambda DG-4

Бренды по названию

Популярные бренды