Sutter Instrument Lambda DG-4 Скачать руководство пользователя

Страница: 36 / 86

LAMBDA DG-4 & DG-5 OPERATION MANUAL – REV.

3.05C

(

20150414

)

Press 5 to view the MOVE ON STROBE PULSE menu.

Press 1 to activate MOVE ON STROBE and return to the MAIN MENU or press 0 to abort

the mode selection routine and retain the current mode setting. The status of the operational

mode will be indicated in the lower line of the MAIN MENU display.

3.7.6

Move on Sync, Inhibited by the Strobe Line Mode

[MODE/6]

This mode combines the functions of the MOVE ON SYNC PULSE and the MOVE ON

STROBE PULSE modes (see above) to allow the capture of more than one video frame before

advancing to the next filter in the previously programmed series of FILTER NUMBERS

(Ring Buffer). In this mode the Lambda DG-4/5 controller will ignore the SYNC input until it

detects a state change in the STROBE LINE, from HIGH to LOW. Then it will advance to the

next filter in synchrony with the next vertical sync pulse that occurs. The computer

interfaced with the Lambda DG-4/5 must be set up to monitor the video signal and hold the

STROBE line HIGH if the number of frames to be captured with each FILTER NUMBER is

to be constant. This option might also be used to solve some timing problems that can result

when using inherently fast software or computers. Selection of this mode is made by pressing

the MODE key followed by the 6 key to get to the MOVE ON SYNC, INHIBITED BY THE

STROBE LINE menu. Alternatively, you can “page” through the mode selection menus by

pressing MODE. The following menus will be displayed:

Press 1 twice to scroll through the NEXT PAGE to see the desired option or press the 0 key

to abort the routine and return to the MAIN MENU.

0=EXIT, 1=NEXT PAGE. 4= MOVE ON SYNC.
PULSE, 5 FOR MOVE ON STROBE PULSE

ADVANCE TO NEXT FILTER ON STROBE IS OFF
PRESS 1 TO TURN ON, 0 TO KEEP IT OFF

10 = FILTER NUMBER, TURBO-BLANKING- OFF
INPUT = MANUAL MOVE ON STROBE PULSE

0=EXIT, 1=NEXT PAGE, 2 = TURBO BLANKING
3 = DISPLAY THE FIRST 4 FILTER VALUES

Содержание Lambda DG-4























































































Результаты поиска

Содержание Lambda DG-4

Отзывы:

Похожие инструкции для Lambda DG-4

Бренды по названию

Популярные бренды

Sutter Instrument Lambda DG-4, Руководство по эксплуатации

Результаты поиска

Содержание Lambda DG-4

Отзывы:

Похожие инструкции для Lambda DG-4

Бренды по названию

Популярные бренды