Sutter Instrument Lambda DG-4 Скачать руководство пользователя

Страница: 33 / 86

LAMBDA DG-4 & DG-5 OPERATION MANUAL – REV.

3.05C

(

20150414

)

Pressing 1 again at this point will not produce further screens.
The above menus are of informational value, only. Once the MODE button has been pressed

any one of the seven operational modes presented (# 2 through 8) can be selected by pressing

the corresponding numeric key. For example, to set the MOVE ON SYNC PULSE mode,

simply press the MODE key, followed by the 4 key to directly access that mode’s menu.

3.7.3

Move on Command Mode

[1 through 15]

Selecting a new filter: The numeric keys.

By default, the Lambda DG-4/5 will be in the

MOVE ON COMMAND mode and under LOCAL control (“manual mode”) when it starts up,

unless remote commands are waiting on an interfaced device connected to an input port. The

default FILTER NUMBER will be 0, yielding no light output. Selection of a new FILTER

NUMBER is made using the keypad, and will immediately yield light through the FILTER

POSITION and at the ATTENUATION level previously programmed for that FILTER

NUMBER value (see the section on SETUP modes). Under LOCAL control, the filter is

selected by entering a value in the range of 0 to 15. If a single digit value is desired, the user

may either press 0 and then the correct numeric key or just the single correct numeric key

followed by ENTER. If the value is a 2-digit number, press the correct 2 keys (1 and then the

second key) but do not press ENTER. Pressing ENTER without first pressing a numeric key

will select 0. Consequently, if you press a 2-digit number correctly and then press ENTER

you will briefly select the filter you desired and then filter 0 (closing the “shutter”). The

following examples demonstrate the two methods of entering a single digit FILTER

NUMBER (8 in this case).
Method 1: The main menu would look like this if the initial FILTER NUMBER = 10

0=EXIT, 1=NEXT PAGE. 4= MOVE ON SYNC.
PULSE, 5 FOR MOVE ON STROBE PULSE

0=EXIT, 1=NEXT PAGE. PRESS 6 FOR MOVE ON
SYNC, INHIBITED BY THE STROBE LINE

0=EXIT, 1=NEXT PAGE. 7 = EDIT A FILTER
DEFINITION, 8 = SETUP THE RING BUFFER

10 = FILTER NUMBER, TURBO-BLANKING- OFF
INPUT = MANUAL MOVE ON COMMAND

Содержание Lambda DG-4























































































Результаты поиска

Содержание Lambda DG-4

Отзывы:

Похожие инструкции для Lambda DG-4

Бренды по названию

Популярные бренды

Sutter Instrument Lambda DG-4, Руководство по эксплуатации

Результаты поиска

Содержание Lambda DG-4

Отзывы:

Похожие инструкции для Lambda DG-4

Бренды по названию

Популярные бренды