Supermicro SC816LTS-655BP Скачать руководство пользователя страница 73

Страница: 73 / 104

Chapter 6: Advanced Chassis Setup

6-5

6-4 Drive Bay Installation/Removal

The SC816LT chassis contains twelve 3.5" and two 2.5" internal fixed hard drives.

Each hard drive and its position in the chassis are labeled with a number that cor-
responds to the SATA port on the motherboard.

Warning!

Enterprise level hard disk drives are recommended for use in Supermicro

chassis and servers. For information on recommended HDDs, visit the Supermicro Web

site at http://www.supermicro.com/products/nfo/files/storage/SAS-1-CompList-110909.

pdf

Figure 6-5. Hard Drive Positions and their Corresponding SATA Ports

Replacing Hard Drives

Replacing a 3.5" Hard Drive

1. Power down the chassis with the operating system, remove the cord from the

rear of the power supply as described in Section 5-3 and remove the front
and rear covers as described in Section 5-4.

2. Locate the latch on the HDD you wish to remove from the chassis.

Press down on the latch to release the HDD from the floor of the chassis.

4. Slide the HDD forward to release it from the mounting bracket that secures it

to the floor of the chassis.

Содержание SC816LTS-655BP









































































































Результаты поиска

Содержание SC816LTS-655BP

Отзывы:

Похожие инструкции для SC816LTS-655BP

Бренды по названию

Популярные бренды

Supermicro SC816LTS-655BP, Руководство пользователя

Результаты поиска

Содержание SC816LTS-655BP

Отзывы:

Похожие инструкции для SC816LTS-655BP

Бренды по названию

Популярные бренды